Harbor Freight Tools Planer 90310 User Manual

DUPLEX RABBET &  
FILLISTER PLANE  
90310  
ASSEMBLY AND OPERATING INSTRUCTIONS  
3491 Mission Oaks Blvd., Camarillo, CA 93011  
Copyright © 2003 by Harbor Freight Tools®. All rights reserved. No portion of  
this manual or any artwork contained herein may be reproduced in any shape  
or form without the express written consent of Harbor Freight Tools.  
For technical questions and replacement parts, please call 1-800-444-3353  
 
9.  
Maintain tools with care. Keep tools sharp and clean for better and safer  
performance. Follow instructions for lubricating and changing accessories. The  
handle must be kept clean, dry, and free from oil and grease at all times.  
10. Stay alert. Watch what you are doing, use common sense. Do not operate any tool  
when you are tired.  
11. Take caution as some woods contain preservatives such as copper chromium  
arsenate (CCA) which can be toxic. When cutting these materials extra care should  
be taken to avoid inhalation and minimize skin contact.  
12. Check for damaged parts. Before using any tool, any part that appears damaged  
should be carefully checked to determine that it will operate properly and perform its  
intended function. Check for any broken parts or mounting fixtures; and any other  
condition that may affect proper operation. Any part that is damaged should be  
properly repaired or replaced by a qualified technician.  
13. Replacement parts and accessories. When servicing, use only identical  
replacement parts. Use of any other parts will void the warranty. Only use accessories  
intended for use with this tool. Approved accessories are available from Harbor  
Freight Tools.  
14. Do not operate tool if under the influence of alcohol or drugs. Read warning  
labels if taking prescription medicine to determine if your judgment or reflexes are  
impaired while taking drugs. If there is any doubt, do not operate the tool.  
15. Maintenance. During periods of storage, coat the bare metal surfaces with light oil to  
inhibit rust.  
Warning: The warnings, cautions, and instructions discussed in this instruction  
manual cannot cover all possible conditions and situations that may occur. It must be  
understood by the operator that common sense and caution are factors which cannot  
be built into this product, but must be supplied by the operator.  
Unpacking  
When unpacking, check to make sure the parts shown on page 5 are included. If any parts  
are missing or broken, please call Harbor Freight Tools at the number on the cover of this  
manual as soon as possible.  
Warning! Do not let the blades come in contact with your hands while planing or changing  
the blades. They are extremely sharp and will cause severe injury if contacted.  
SKU 90310  
Page 3  
 
Operation  
Refer to the Assembly Drawing on page 5 and FIGURE 1 below.  
Note: The front blade (fillister) is stationary and the rear blade is movable and replaceable.  
1. To change or replace Blades, turn the Blade Removal Knob (see below) counterclockwise  
and lift off the blade holder (see below). Set the Blade in so that it fits over the set screw and  
is properly aligned. Replace the Blade Holder and tighten the Blade Removal Knob.  
2. Adjust the amount of blade you want to contact the workpiece by pressing the Blade  
Adjustment lever side to side (see Assembly Drawing on page 5).  
FIGURE 1  
Blade Removal Knob  
Blade Holder  
Blade  
Set Screw  
3. There are two fences. To adjust the Depth Gauge Fence, loosen the Lock Screw and move  
the Fence up or down to determine the depth you cut into the wood (see Assembly Drawing  
on page 5). To assemble the Fence located on the left side of the tool, first thread on the Steel  
Rod into the left side of tool’s housing. The Fence slides over the end of the Steel Rod and is  
locked in place by the Fence Adjustment knob. To adjust this Fence (determines width of  
cutting area), loosen the Fence Adjuster knob and move the Fence either closer or further  
from the body of the Planer. With the Fence in the desired position, secure it in place by  
tightening the Fence Adjuster knob.  
4. Make sure the workpiece is securely fastened down.  
Note: If you are using the front blade for bullnosing (See Assembly Drawing on page 5), make  
sure the rear blade is adjusted up so it doesn’t contact the workpiece.  
5. Do not force the Plane or press down on it. Move it forward, taking off a little wood at a  
time. If the Plane does not move forward easily, retract the Blade more as explained in step  
2 above.  
SKU 90310  
Page 4  
 
Assembly Drawing  
Handle  
Blade Adjustment  
Lever #8  
Blade #1  
Blade Removal  
Knob #7  
Fence #4  
Fence Adjustment  
Lock Screw #6  
Steel Rod #3  
Lock Screw #5  
Note: This Plane includes two blades  
and two fences.  
Depth Gauge Fence #2  
Front Blade  
REPLACEMENT PARTS  
#1  
#2  
#3  
#4  
#5  
#6  
#7  
#8  
Blade  
Depth Gauge Fence  
Steel Rod  
Fence  
Lock Screw  
Fence Adjustment Lock Screw  
Blade Removal Knob  
Blade Adjustment Lever  
Maintenance  
1. Keep the Blades sharp and clean.  
2. Do not allow wood residue to build up on the blades.  
3. Wipe the Plane down with a lint free cloth regularly.  
PLEASE READ THE FOLLOWING CAREFULLY  
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS  
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBU-  
TOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE  
OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS  
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER  
AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS  
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE  
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER  
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING  
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.  
NOTE: Some parts are listed and shown for illustration purposes only and are not available  
individually as replacement parts.  
SKU 90310  
Page 5  
 

Havis Shields Automobile Accessories C TM EXPD User Manual
Honeywell Home Security System K5305 1V5 User Manual
Hoshizaki Ice Maker KM 1900SAH 3 User Manual
HP Hewlett Packard Network Cables HP 85025C User Manual
HTC Cell Phone Thunderbolt User Manual
Humminbird Fish Finder 967C User Manual
Husqvarna Saw TS 66 R User Manual
Hypercom Network Card C5100 User Manual
IKEA Plumbing Product AA 338731 2 User Manual
IMC Networks TV Converter Box 9403 User Manual