Harbor Freight Tools Outdoor Fountain 90326 User Manual

MOUNTABLE WALL SINK  
90326  
ASSEMBLY AND OPERATING INSTRUCTIONS  
3491 Mission Oaks Blvd., Camarillo, CA 93011  
Copyright © 2003 by Harbor Freight Tools®. All rights reserved. No portion of  
this manual or any artwork contained herein may be reproduced in any shape  
or form without the express written consent of Harbor Freight Tools.  
For technical questions and replacement parts, please call 1-800-444-3353  
 
10. Stay alert. Watch what you are doing, use common sense. Do not operate or  
assemble the Sink when you are tired.  
11. Check for damaged parts. Before using any product, any part that appears  
damaged should be carefully checked to determine that it will operate properly and  
perform its intended function. Check for alignment and binding of moving parts; any  
broken parts or mounting fixtures; and any other condition that may affect proper  
operation. Any part that is damaged should be properly repaired or replaced by a  
qualified technician.  
12. Replacement parts and accessories. When servicing, use only identical  
replacement parts. Use of any other parts will void the warranty. Only use accessories  
intended for use with this product. Approved accessories are available from Harbor  
Freight Tools.  
13. Do not operate the Sink if under the influence of alcohol or drugs. Read warning  
labels if taking prescription medicine to determine if your judgment or reflexes are  
impaired while taking drugs. If there is any doubt, do not operate the product.  
14. Maintenance. For your safety, service and maintenance should be performed  
regularly by a qualified technician.  
Warning: The chrome covered copper tubing on the Faucet (Spout (#6)) is very delicate and  
should be handled with care. Do not lift or pull on the Faucet (Spout (#6)).  
Warning: The warnings, cautions, and instructions discussed in this instruction manual  
cannot cover all possible conditions and situations that may occur. It must be under-  
stood by the operator that common sense and caution are factors which cannot be  
built into this product, but must be supplied by the operator.  
Unpacking  
When unpacking, check to make sure the partslisted on page 7 are included. If any parts  
are missing or broken, please call Harbor Freight Tools at the number on the cover of this  
manual as soon as possible.  
WARNING: The brass components of this product contain lead, a chemical known to the  
State of California to cause birth defects (or other reproductive harm). (California Health &  
Safety code 25249.5, et seq.)  
SKU 90326  
Page 3  
 
Assembly  
FIGURE 1  
(Overa
FIGURE 2  
Upper Drain  
Connection  
Pin Holes  
Water Inlet  
(Attach 3/4” Hose)  
(not included)  
Pipe (#8)  
Water Outlet  
(Attach 3/4” Hose)  
(not included)  
Elbow (#9)  
Elbow (#9) connects to  
Drain Set (#11)  
SKU 90326  
Page 4  
 
Assembly (continued)  
Note: When deciding where to mount the  
sink, make sure the wall can handle the  
weight of the sink and at least the weight of  
10.5 gallons of water (8 Lbs. per gallon). We  
recommend mounting into wall studs. Plan  
the Sink to be located near the water source.  
FIGURE 3  
Refer to FIGURES 1,2,3,4,5.  
1. Attach the two Wall Supports (#3) to the  
Sink by meshing together the Pins on the  
Wall Supports (#3) next to the Pin Holes on  
underside of each side of the Sink.See  
FIGURE 2. Once the Sink is fully attached  
to the Wall Supports (#3), fit the four  
Mounting Brackets (#1) onto the  
Rectangular Support Ends on each Wall Support (#3). The Mounting Brackets (#1) will  
fit into the gap between the Rectangular Support End and the vertical bar of the Wall  
Support (#3). Hold the Sink, with the  
FIGURE 4  
Rectangular  
Support Ends  
supports and brackets, up against the  
wall. Use a level to make sure the Sink  
is perpendicular to the ground, and mark  
where each screw hole on the  
Mounting Brackets (#1) should go.  
After marking your mounting spots,  
detach the Sink from the  
Wall Supports (#3), and remove the  
Mounting Brackets (#1) from the  
Wall Supports (#3)  
Wall Supports (#3).  
Mounting Bracket (#1)  
2. Screw the Mounting Brackets (#1) to  
the wall (screws not included). See  
FIGURE 3.  
FIGURE 5  
3. Fit the four Rectangular Support  
Ends on each Wall Support (#3) into  
the gap between the Rectangular  
Support End and the vertical bar of the Wall  
Support (#3). See FIGURE 4.  
Pins  
4. Fit the three Pins on each Wall  
Support (#3) to the Sink by meshing  
together the Pins on the Wall  
Supports (#3) with the corresponding  
Pin Holes on underside of each side of  
the Sink.  
SKU 90326  
Page 5  
 
Assembly (continued)  
5. To install the Drain Set (#11):Set the Drain  
FIGURE 6  
Ring into the hole in the Sink. Hold the  
Gasket and the Funnel under the Sink in  
positionunder the hole. Attach them with the  
screw. See FIGURES 2 and 6.  
Screw  
6. Attach the Elbow (#9) to the Funnel with  
the Connector (#10). See FIGURE 6.  
7. Attach the Pipe (#8) into the Elbow (#9)  
in the bottom, and the piece of pipe coming  
from the upper drain on the top.  
Drain Ring  
Gasket  
Funnel  
See FIGURES 2 and 6.  
FIGURE 7  
8. Set the Spout (#6) into the hole next  
to the upper drain and connect it under  
the Sink with the Spout Connector (#6).  
Attach the Intake Coupler (#12) to the  
Spout Connector (#6).  
9. Attach a 3/4” hose (not included) to the  
threaded Water Inlet. See FIGURE 2.  
Attach a 3/4” hose using hose clamps  
(not included) to the Water Outlet. Route  
hose to your planned location for waste  
water exit.  
10. Check the Sink and all the fittings for  
leaks and that it properly drains. Once  
you’re sure that everything is satisfactory,  
the Sink is ready for use.  
FIGURE 8  
Note: The small tray and the washboard  
tray easily set in the top of the Sink when  
needed. See the cover photo.  
Maintenance  
1. Periodically check that all of the  
connections are tight.  
2. Keep the drain clear of all obstructions.  
SKU 90326  
Page 6  
 
Parts List and Assembly Drawing  
1
7
8
2
Part No.  
1
2
Description  
Mounting Bracket  
Sink  
Qty.  
4
1
9
3
4
5
6
7
8
9
10  
11  
12  
Wall Support  
Washboard  
Tray  
Spout/Spout Connector  
Hose Coupler  
Pipe  
2
1
3
10  
1
1 each  
1
1
1
1
1
1
11  
Elbow  
Connector  
Drain Set  
Inlet Coupler  
4
5
6
12  
6
PLEASE READ THE FOLLOWING CAREFULLY  
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS  
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBU-  
TOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE  
OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS  
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER  
AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS  
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE  
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER  
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING  
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.  
NOTE: Some parts are listed and shown for illustration purposes only and are not available  
individually as replacement parts.  
SKU 90326  
Page 7  
 

Graco Automobile Parts 234397 User Manual
Greenheck Fan Ventilation Hood SEBR 10 User Manual
Grizzly Saw G0636X User Manual
Grizzly Saw G0716 User Manual
Hearth and Home Technologies Ventilation Hood ST1175 User Manual
Heat Glo LifeStyle Outdoor Fireplace DAKOTA 42 User Manual
Hotpoint Oven S220E User Manual
HP Hewlett Packard All in One Printer M9050 MFP User Manual
HP Hewlett Packard Personal Computer dx2700 MT User Manual
i mate PDAs Smartphones PDA2K EVDO User Manual