Environmental-friendly Double
Drive Washing Machine
User's manual
This manual is for
HWM70-0588H
Please read this manual
carefully before using.
Retain it for future reference.
Names of the parts
Packing list
× ° Ï ä Ë μ Ã ÷
Water inlet valve
Water absorption gasket
One
One
User's manual
Warranty card
Inside the document bag
Inside the document bag
Top lid component
Inner cover
Detergent box
Control panel seat
Outer tub cover
Balance ring
Power cord
Screw cover
Hook
Components of the water inlet
hose
Cabinet handle
Drain hose
Attach block
One
Inside the accessory bag
Inner tub
Lint filter
Pulsator
Front control board
Cabinet
Front door
Drain
protective lid
Bottom plate
Back cover
Drain protective lid
Base frame
Between the upper cushion of the washing
machine package and the upper seal of the
package carton
One
Liquid blenching filler
Adjustable leg
Fixed leg (3 pieces)
Inner cover
component
One
Inside the accessory bag
Meaning and description of the symbols
Automatic washing machine
One
Warning sign
Contents marked with that symbol are related to the
safety of the product and the personal safety of the users.
Please operate in strict conformity to the contents.
Forbidden sign
Contents marked with that symbol are actions forbidden
to perform. Performing of those action may result in damage of
the machine or influence the personal safety of the users.
1
Trouble-shooting answer to question
Safety precautions
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes.
Please confirm again before sending it to repair. Do not repair it by yourself.
The washing machine must be positioned
Please plug the power plug on special
receptacle. Be sure to use three-pins
power receptacle. Ensure that the earthing
prong of the power receptacle is earthed
reliably. Use leakage protector if possible.
Phenomena
The reason
How to settle
so that the plug is accessible. Be sure to pull the
plug off and close the water faucet in
following cases: power failure, delivering
the machine, setting the machine idle or
c l e a n i n g t h e m a c h i n e . D o n o t p l u g
or pull the power plug with wet hand.
Close the top lid.
The digitron displays E0.
The top lid is opened during reserve procedure.
The drainage cannot work, or is too slow.
The digitron displays E1.
Is the drain hose put down?
Is the drain hose blocked?
Put down the drain hose. Open and close the top lid once.
Clean the foreign material. Open and close The top Lid Once.
It stops running in midway. The digitron
displays E2.
The top lid is not closed.
Close the top lid.
Do not bend ,extend, twist, bind by force. Do not press or nip it with weight.
Keep the pin of the power plug clean, if the power plug is polluted with dust, please wipe with
dry cloth carefully.
If the power cord or the power plug is bad, to avoid risk it is required to have it replaced by
the technicians of our special shop or our customer care agent.
The safety switch acts, and the
spinning cannot work. The
digitron displays E3.
Are the laundries put slantingly?
Is the machine slanting?
Reorder the laundries. Close the top lid.
Th machine will start running after 10
seconds of being placed horizontally.
Open the water tap. Push the start/Pause
button once.
Clean the water inlet valve then push
the Start/Pause button once.
Push the Start/Pause button once.
Is the water tap opened, or is there water
supply failure?
Is the water inlet valve blocked?
Is the water pressure too low?
The water filling does not work, or is
slow. After about 15 minutes later,
the digital displays E4.
Please contact the after-sales
service department.
The digitron displays E6.
The digitron displays E7.
The digitron displays EE.
The water level sensor is bad.
The communication is bad.
In case the washing machine is installed on ground with
carpet, do not block the ventilation hole with carpet.
Do not use water hotter than 50
.
Please contact the after-sales service
department.
Clean the water inlet valve then push
the start/Pause button once.
Push the Start/Pause button once.
Is the water inlet valve blocked?
Is the water pressure too low?
The ventilation
holes at the bottom
Carpet
Is there power failure?
Is the power plug inserted tightly?
Is the water level reached preset position?
Please use it when there's power supply.
Insert the power plug tightly.
Fill water to the preset position.
Not wash
The machine does
not act
Is the power plug inserted tightly?
Is the top lid closed reliably?
Are the laundries set flat?
Insert the power plug tightly.
Close the top lid.
Set the laundries flat.
Not spin
Adjust the machine to be even
Reorder the laundries and close the top lid.
Remove the foreign materials.
Is the machine slanting?
Are the laundries put slantingly in spinning?
Are there any foreign materials?
Do not put the machine at damp place like
the bathroom. Never wash it with water. Do
not put wet laundries on the control panel.
There's abnormal sound
inside the machine
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.
Is the screw of the jointer of water
inlet hose loose or awry?
Fasten the screw of the jointer properly.
The water tap leaks
Common phenomena
Phenomena
Explanation
Balance the laundries to avoid slanting.
The spinning is intermittent when it starts.
The wash procedure is paused.
The cloth sensor is checking the cloth, it willadd waterafter 48 seconds.
The program is setting the drain time. Some time is needed
before it starts spinning.
Push the PROGRAM button to select SPIN,
but it doesn't work.
The pulsator pauses during water inlet
in wash and rinse.
Do not let the machine share one receptacle with other
electric appliances. If the plugging into the receptacle
is loose, do not use the plug any more.
It is to avoid splashing during water inlet.
There may be some water flowing out of the
drain hose in the first use of the machine.
It is the water remained in the factory inspection of performance.
When NO Detergent is selected, water drained from the drain pipe during the filing
process is sterilizing and can be used to sterilize the sewerage or mops. When
Disinfection is selected, water drained from the drain pipe during the filling process
is disinfecting and can be used to disinfect the sewerage or mops.
Select the No Washing Powder or Disinfect
There may be some water flowing out of the
drain hose in the use of the machine.
2
Disposal after washing
Safety precautions
After using, please clean the lint and foreign materials of the lint filter etc. in time.
Otherwise it may influence your using the machine.
Do not put hand into the rotating tub. It is dangerous
even if the rotation speed is slow. Take special care of
the children. Keep children away from the washing
machine to avoid them climbing on.
Do not decompose, repair or alter the machine by
yourself.
Please first pull off the power plug from the receptacle before cleaning.
The lint filter must be used during washing.
It must be cleaned in time after each using.
Lint filter:
1.Push down the spring piece of the top lint filter
to make the claws out of the filter cover, and then
pull out the lint filter to get it down. figure1
2.Pull the back of the lint filter, and then you can
get down it off the front cover of the lint filter. figure2
3.Sweep the rubbish in the lint filter.
Clean the detergent box and set it on
the control panel seat.
1.The method of dismantle: Push it up aslant and gently.
2.The method of install : install it upwards and aslant
and push it in .
Do not put any hot or heavy items (such as the
kettle with hot water) on the washing machine.
Do not wash laundries with volatile materials
(such as thinner, petrol etc.).
4.Put the back of the lint filter into the front cover .
5.Put the lint filter into filter cover, and make it
tight .
trol
Pe
Benzene
6.Make sure the lint filter well installed, or it can
influence your use.
The back cover of lint filter
Up
Up
Dismantle
Dismantle
Dismantle
Install
Install
Install
Down
Keep the machine away from direct sunlight and
heat source like the heater.
The handicapped or children without care shall not use
the machine.
The front cover of lint filter
Figure 2
Down
Figure 1
The filter screen of the water inlet valve is likely to be
blocked by foreign materials and influence the water
inlet.
If the cabinet is dirty, wipe it with wet cloth
Do not flush it directly with water.
Please clean it with brush every two months.
Wipe it with neutral detergent.
Do not wipe it with thinner, petrol, alcohol etc.
r
e
Petrol
Alcohol
Thinn
Please keep the lint filter in good condition,
and install it to proper position during
washing. If the lint filter is lost or
To protect your laundries and washing machine,
please take out all of the coins, buttons, sand, hairpin
and other foreign materials before washing.
Install
Dismantle
damaged, please contact the customer
care agent of our company.
.
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).
Please check if the water faucet is open, and if the connection of the water inlet pipe is proper.
It is suggested to use foamless washing powder.
2.Do not store water in the washing machine for a long period. Drain the water completely after each using.
3.Be sure to pull off the power plug before maintenance.
To change the direction of drain pipe, please contact the customer care agent of our company.
4.Hang up the power cord and drain hose.
Please don t use the washer in the environment below 0 C; if the washer has been stored below 0 C,
please be sure to ensure the washer is placed under the room temperature for 24 hours and then use
otherwise the washing effects may be lowered or the washer may be damaged.
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time
(about 1 hour), then close the top lid.
Installation and adjustment
Please install and adjust the machine according to the requirement of the manual.
It is very important to your security and correct operating the machine.
3 Push "SOAK" "WASH/SPEED" "RINSE" "SPIN/SPEED"
button to select suitable procedure program
Install the Inner cover component
Attention
Before initial use of the machine, assemble the inner cover as described below:
1.Open the top lid of the washing machine.
2.Put the inner cover component on the outer tub cover, aiming
the inner cover shaft to the installation hole of the
corresponding outer tub cover shaft groove.
Even there's no water in the tub, a certain period is required before spin starting.
Separate the laundries that are not colorfast from other laundries in washing.
The soak procedure can work in cooperation with automatic programs like normal, comforter
There is intermittent pulsator stirring during soak.
After the machine starts operation, you can only set the program and procedure during washing,
and can not make setting in other cases.
Outer tub cover
Outer tub cover shaft groove
Inner cover shaft
Inner cover
If the water pressureis too low,in order to washthe cloth cleanly,the machine will change
from " SAVING WATER"to "storing water "automatically.
Damping cushion
4 Push the " WATER LEVEL "button, select
suitable water level
3.Firstly insert the inner cover shaft of one side into the corresponding
outer tub cover shaft groove, then push the another inner cover shaft
into the corresponding outer tub cover shaft groove. Please install to
designated position to guarantee there are no dropping or abnormal
sound in opening and closing of the inner cover, and the operation shall
be smooth. Do not dismount the inner cover component after washing.
After switching on the power, the washing machine will execute fuzzy program automatically to detect the cloth.
After defection, it can set the water level automatically. To select other water level, first push the "START/PAUSE"
button, then push the "WATER LEVEL" button to set the water level.
Section I enlarging
5 Push the "FUNCTION" button to select suitable function
Push the"function" button to the selected function digitron lighting.Refer to"function"button in
page 11 for selection.
As the "no detergent" digitron is off ,the using powder program can be selected.
Push
Install the bottom plate
6 Push the "RESERVE" button to select suitable reserve wash
program
After switching on the power, the reserve program is set to off mode automatically. If you need to
set the washing procedure to be finished at reserved time, please push the " RESERVE " button to
set the reserve wash program. Refer to reserve button in Page 11 for selection.
After you open the package, please lean
the washing machine gently down on soft
items ( like the towel cloth, blanket, etc. ).
I
Back
Install the bottom plate to the bottom of
the machine, then lift the machine up
gently. See to the figure:
Confirm the operation of reserve program
Front
When the "RESERVE" function is activated, the indicator light of the program you
have set will be off. The "reserve (hour)" and "time remain" indicator lights will
be on. During reserve procedure, push the "RESERVE" button to display the reserve mode.
To change the running program or cancel the reserve setting, you
Bottom plate
Soft items
Section I enlarging
need to switch off the power and make new selection.
Two claws at the bottom cover shall
be inserted in two bar-shaped holes
in the stand. Make sure the claws
are firmly in place.
7 Push the "START/PAUSE" button
6 Finish washing
After finishing wash it'll alarm and switch off power automatically
Install the water inlet hose
Confirm the water faucet
Water faucet,suitable
"FUNCTION"button
During the normal,saving,speedily and comforter program,press the"function"button to
select washing function procedure.
Selecting the"no detergent"function the no detergent digitron is on,the largest washing
Reserve, remain time digitron
It displays "--" during detecting.
Water faucet,not suitable
rated is 4.0kg.the highest washing water level is"8".
Selecting the"disinfect"function,the "disinfect"digitron is on.
It displays remained reserve time (hour).
It displays total remained time (min). If the total time
exceeds 99 minutes, it uses "A" on tens digit to
represent100 minutes, and uses "b" to represent 110
minutes. E.g. "A3" represents 103 minutes.
It displays abnormal symbol in abnormal situation.
(See to Page15)
Not select the"no detergent"function the no detergent digitron is off, you can use the powder
program.
As you select the"woollen","carpet"program,pressingthe "function"button.the
washing machine has no reaction.Pleaseuse the detergent destined for the
washing laundries.
Outlet end surface
As you select the "standard" program,pressing the"function"button.the washing machine
has no reaction.Please select the"normal"program.
>10mm
As you select the"delicate"program,pressingthe"function"button.the washing
machine has no reaction.Pleaseselect the"saving"program or the"speedily"program
It is required that the front end shall be longer than 10mm.
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.
"POWER" button
Push the "POWER" button to switch on the power.
Under power-on mode, push it to switch off the power.
Push the "POWER" button to switch on the power. If
the "START/PAUSE" button is not pushed, the machine
Remain
Program
Air dry
10
8
6
9
7
5
3
Normal
Saving
Standard
Connection between the water inlet hose jointer and the water faucet
Function
Woollen
Carpet
will switch off the power automatically after 5 minutes.
No
detergent
Speedily
6min
4
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the
water inlet hose component. See to Figure 1.
Comforter
Disinfect
Delicater
2
1
Reserve
2. Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen
the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth,
otherwise it may leak water. See to Figure 3.)
Program
ry
Air d
Reserve
LOCK
water inlet hose jointer
Screw
Slider
Sign plate
Screw knife
Bushing
Figure 3
"PROGRAM/AIR DRY"button
Lock level
"WATER LEVEL"button
"RESERVE" button
Following full-auto program is available
The washing machine can detect the laundries automatically.
After detection, it will set the water level to suitable value among
4, 6, 8,and 10 automatically.
You can also set water level by yourself. After the machine is
started, it will not set water level automatically. You shall push the
start/pause button to make new setting.
If there's water inside the tub, the machine cannot detect the
laundries and will display water level 6 .If wet laundries are put
in, it may display water level 10. You must set suitable water level
by yourself.
The digitron displays the time
remained (in minute) before
the washing is finished.
water inlet hose
Program
Normal Washing for normal laundries
Application
Figure 2
Figure 1
Push down the reserve
Saving
Speedily
Quick washing for normal laundries
Washing for light-soil a few laundries
button. The reserve indicator
light is on the digitron displays
the reserve time of finishing
washing (in hour).The time
remain indicator light is on,
indicating that the reserve
function is running.
3.Fasten the four screws evenly. See to Figure 4.
4 Take off the nameplate. Twist the fastening nut as per the indication of the figure
to seal up the exit end face of the faucet. See to Figure 5.
Comforter Washing for big and thick laundries
Standard
Standard saving washing for normal laundries
If Speedily program is selected, it will display water level 3 .
When water level 2 is reached in water filling, it will perform
washing while filling water. When water level 3 is reached, it will
change to normal washing.
Woollen Washing for the woollen laundries,
under 2.5kg
remark: Before installation, the threading is 4mmabove the upper surface of the nut.
After installation, the threading is 2mm above the upper surface of the nut. See to figure 6.
Push the reserve button can
display the reserve state.
Carpet Washing for carpet and wearing bigger
Laundries, under 3.0kg
During operation of wash and rinse program, you can push down
the water level button to add water. When you release the button, or
it reaches the overflow water level, the machine will stop adding
water.
Delicate
Saving washing for light-soil laundries
About 4mm before twisting
About less than 2mm after twisting
Push down the programbutton continuously
for more 2 seconds.After a beep sound,
the program is changedinto the Airdry
program.then push the programbutton to
select the different airdry time(0.5,1 ,2, 3
hours)
The water level decided may be different from actual value because
of the different moisture level of the laundries.
All the program that When water level 1 is reached,it will perform
washing while filling water.When water level set is reached, it will
change to normal washing.
Screw nut
Figure 5
Figure 4
Figure 6
You can set speedily woollen carpet delicate program by
yourself, never changed. It is to set water level 8 highest during
the standard program.
5 Use the operation button
Description of operation button
Connection between the water inlet hose and the washer
a
Child lock function
The function is intendedfor children safety and preventing the washing
program from accidental changesby children.
Indicator mode and meaning
1.Do not take off the water absorption cushion. Please check if the
nut of the water
cushion is dropped or damaged before each usage. If it happens
inlet hose
Push and hold the waterlevel button and spin button, then push down the
power on/off button .Thedigitron displays C L .You can continuesetting
desired washing procedures.After setting ,push downthe start/pause
button. The child lockfunction is activated. all of the buttons are locked
and cannot make selection .
Flashing, indicating the running program
please contact our after-sale department immediately.
On, indicating the program about to run or the selection mode
2 .Put the nut of the water inlet hose on the valve jointer.
3 .Fasten the nut. Swing it gently to confirm if it's suitable.
Release the child lock function :push down waterlevel button and spin
button at the same timefor more 2seconds .Aftera beep sound ,the child
lock function is released.
jointer of the
water inlet valve
water absorption
cushion.
"START/PAUSE" button
After the poweris switched on, press it to
start the machine
During working, push it to pause.
During pause, push this button to restart
and go on working
Wash/spin
speed
Wash
Spin
Rinse
Connection between the jointer of the water inlet hose and the water inlet hose
4
Soak
2
1.Push down the slider. Insert the water inlet hose into the jointer.
the jointer of the
water inlet hose
Overflow
Locking level
Slider
2 Hang the lock lever to the jointer. Release the slider till a click
sound is heard.
SPIN
SPEED
Check the connection between the jointer of the water inlet hose
and the water faucet
1.Swing the hose gently to confirm if it is fastened stable.
2.After installation, open the faucet to check if it leaks.
3.Do not bend the hose with overstrain.
4.Before each usage please check if the connection
between the jointer of the water inlet hose and the
water faucet, and the installation of the water inlet
hose are firm, so as to prevent dropping from
improper installation position.
"SPIN/SPEED " button
Press the Spin/Speed button to
select a spin procedure.
The button can beused to select
the desired spin time(1,3,5,7
minutes )from the Normal program
or the Comforter program.
The button is unavailablefrom the
Saving,Speedily, Standard,Woollen,
Carpet and Delicate programs.
"SOAK "button
"WASH/SPEED " button
"RINSE" button
Press the Soak buttonto select a soak
procedure.
Press the Washbutton to select a
wash procedure.
The button can beused to select
the desired wash time(0,6,9,12,15
minutes) from the Normal and
Press the Rinse buttonto select a
rinse procedure.
The button can beused to select the
desired soak time( 10,20 minutes)
from the Normal andComforter
programs.
The button can beused to select
the desired number ofrinse cycles,
(0, 1, 2 ,3 times )from theNormal
program or the Comforterprogram.
While the "Overflow" digitron is
lighting,the program of theoverflow
rinse has been selected.
Comforter program.
The button is unavailablefrom the
Saving,Speedily, Standard,Woollen,
Carpet and Delicate programs.
For a pause duringoperation or an
initial operation, press thebutton
for 2 seconds tostart wash speed
selection. The Washindicator lamp
is on and thespeed from 1 to4 is
available for selection.The default
value is 2.After restart, the machine
is back to washselection.
The button is unavailablefrom the
Saving,Speedily, Standard,Woollen,
Carpet and Delicate programs.
For a pause duringoperation or
an initial operation, pressthe
button for 2 secondsto start spin
speed selection. TheSpin
indicator lamp is onand the
speed from 1 to4 is available for
selection. The defaultvalue is 2.
After restart, the machine is back
to spin selection.
The button is unavailablefrom the
Saving,Speedily, Standard,Woollen,
Carpet and Delicate programs.
Dismantle the water inlet hose
For the Normal program,the Water
Saving mode is selected
automatically. Ifthe button is
pressed before operation, it will
change to WaterFilling mode.
1. Close the water faucet.
2. Press the locking lever. Push down the slider. Then pull of the water inlet
hose.
Press the button for2 seconds.
There is a buzzthat indicates the
speed selection is complete. Then
the wash cycle canbe selected.
Locking level
Press the button for2 seconds.
There is a buzzthat indicates the
speed selection is complete.
Then the spin cyclecan be selected.
Note: No speed selectionfrom the
Woollen, Carpet andDelicater
programs.
If the machine is used frequently, the jointer of the water inlet hose can be
on the faucet to prevent damaging the fixing screw.
Slider
kept
1 Preparation before washing
2 Put in the laundries
Preparation before washing
1.Connect the water inlet hose.
The capacity of washing of the machine refer to the largest weight of the
standard laundries under dry condition that can be washed in one
time. Laundries quantity in one washing cycle shall be lower than
the standard capacity.
2.Confirm that the washing machine is earthed
reliably. Then insert the power plug into the
receptacle. Do not connect the earth terminal
to the gas pipe and tap water pipe.
3.Put down the drain hose.
The thickness ,size , type of the cloth will influence the actual washing capacity.
It is suitable to put in reasonable amount of laundries and the laundries can be turned
round in washing for one time washing.
Do not select " 4" water level for laundries less than 1.0kg ,so as to avoid
splashing of water.
3 Usage of detergent
Control panel seat
Washing powder inlet
Liquid detergent inlet
4.Slanting or uneven ground may result in
unstable working or abnormal noise. Please
make the machine stand horizontally.
Detergent box
How to use washing powder
Pay attention to followings before washing the laundries
When " FUNCTION " button not selected for
using washing powder program please
determine the consumption of washing powder
as per the operating instruction of washing
powder, clothes load and dirtiness.
When selecting "No washing powder” function
if add a small quantity of detergent the clothes
will be washed cleaner.
It is suggested to add washing powder into the box
directly under fuzzy program and reserve program.
Clear the pocket.
Take out the coins ,
sand, hairpins etc.
Confirm if there's
special requirement
for the laundries.
The quantity of the
laundries shall not
exceed the rated
value. The big
Dissolve directly inside the washing machine: (not
applicable for fuzzy and reserve program)
1.Add some water(select " 1 " water level).
Fasten the buttons
and zippers.
When the pulsator is
running ,the buttons of
the laundries may cause
noise. For the sake of
discretion ,please put
the laundries with
buttons into other
2.Add washing powder. Run for about 30s to fully dissolve
Powder. Then push the"START/PAUSE" button.
the
laundries like the
jeans shall be put
in loosely.
3.Put in laundries. Select suitable water level. Push the
Button again.
"START/PAUSE"
Quick dissolving of washing powder:
1.Prepare warm water of 30 C and container.
2. Add washing powder while stirring to dissolve it completely.
laundries.
How to use whitener
When choosing the " No detergent" program, the usage of
softener or whitener is same as using detergent.
Please add suitable washing powder as per the laundries
quantity, the set water level and water quantity.
If you select "Speedily" program, it is suggested to use
liquid detergent instead of washing powder to guarantee
the washing effect.
Add water to stipulated level. Dilute the whitener with container,
and then pour it into the liquid whitener inlet slowly.
Laundries with color or pattern is not colorfast, thus not applicable.
It is not recommended to use rich-foam washing powder.
The whitener shall not touch laundries directly.
See to the manual of whitener for the usage and dosage.
For whitener in powder, dissolve it before use.
a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries with unfast color from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
Washing powder with poor quality or long-time storage may
get caked. Please clean the detergent box duly in usage.
d. For those laundries with heavy soil, please first remove the dirt like mud or dust. For the parts with heavy soil,
please apply detergent in advance, which can make it easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur, turn it over before putting in.
f. Do not put those laundries polluted by chemicals directly into the washing machine.
g. For those small laundries and those may get twisting or worn, and woollen/fur laundries, please put them into
mesh bag for washing.
4 Close the top lid
As the top lid opened, the washer will automatically given alarm and stop running, exclusively during draining.
|