MODEL T10877
CANISTER FILTER
FOR G0710/G0710P
INSTRUCTIONS
For questions or help with this product contact Tech Support at (570) 546-9663 or [email protected]
Introduction
Inventory
This kit includes everything you need to upgrade
your G0710 or G0710P dust collector with a
1-micron canister filter and plastic collection bag.
Description
Qty
A. Canister Filter ............................................. 1
B. Collection Flange........................................ 1
C. Connection Collar....................................... 1
D. Bag Clamp.................................................. 1
E. Collection Bag............................................ 1
F. Clean-Out Crank Handle Assembly........... 1
G. Adhesive Foam Strips (Not Shown)
The canister filter is equipped with an internal
cleaning system that is operated by the external
crank handle. Rotating this handle 5 or 6 times
will knock loose any built-up dust inside the filter,
thereby improving airflow. The plastic collection
bag is replaceable, so it can be tied off and dis-
posed of—without increasing your exposure to
fine dust.
Short (For Flange)...................................... 1
Long (For Filter).......................................... 1
H. Hardware Bag (Not Shown)
Flange Screw 1⁄4"-20 x 3⁄4"........................... 6
Flat Washer 5⁄16" ......................................... 4
Hex Nut 5⁄16"-18 ........................................... 2
Hex Bolt 5⁄16"-18 x 2"................................... 2
Open-End Wrench 10 x 12mm................... 1
B
C
A
D
Properly seal all connection points when
installing filter kit to reduce potential expo-
sure to fine dust from leaks.
F
E
Installing Canister Filter
1. DISCONNECT MACHINE FROM POWER!
2. Remove bag clamp and filter bag from G0710/
Figure 1. Model T10877.
G0710P collector body.
COPYRIGHT © APRIL, 2015 BY GRIZZLY INDUSTRIAL, INC.
NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
(FOR MODELS MFD. SINCE 03/15) #WK17321 PRINTED IN TAIWAN
V1.04.15
5
5
7. Install (2) ⁄16"-18 x 2" hex bolts, (4) ⁄16" flat
8. Attach canister filter to flange with (6) 1⁄4"-20 x
5
3
washers, and (2) ⁄16"-18 hex nuts into con-
⁄4" flange screws (see Figure 7).
nection collar, then tighten, making sure
ridges in collar mate with ridges in flange and
collector body outlet (see Figure 6).
9. Attach long foam strip to groove around bot-
tom of canister filter (see Figure 7).
Note: Tug flange by hand to make sure it is
secure before proceeding.
10. Place collection bag over bottom of canister
filter and secure with bag clamp, making sure
clamp is seated in groove over foam strip
(see Figure 7).
Bag
Clamp
Collector
Body
Flange
Screws
Canister
Filter
Collection
Bag
Long Foam
Strip
Figure 6. Connection collar secured firmly in
place around collection flange and outlet.
Figure 7. T10877 final assembly on dust
collector.
T10877 Parts Breakdown and List
27
10
26
25
26
31
4
8
2
11
12
15
24
9
15
12
34
11
28
16
4
3
6
5
1
6
14
30
21
17
7
28
13
20
8
29
19
17
12
15
18
32
23
22
33
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
PT10877001
CANISTER FILTER 15" x 16-3/16"
MAIN SPINDLE
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
PT10877018
PT10877019
PT10877020
PT10877021
PT10877022
PT10877023
PT10877024
PT10877025
PT10877026
PT10877027
PT10877028
PT10877029
PT10877030
PT10877031
PT10877032
PT10877033
PT10877034
CLEAN-OUT CRANK HANDLE
HEX BOLT M6-1 X 16
2
PT10877002
PT10877003
PT10877004
PT10877005
PT10877006
PT10877007
PT10877008
PT10877009
PT10877010
PT10877011
PT10877012
PT10877013
PT10877014
PT10877015
PT10877016
PT10877017
3
CRANK SPINDLE
CRANK HANDLE M10-1.5 X 14, 98L
LOCK NUT M10-1.5
4
BEVEL GEAR
5
BEARING PLATE
COLLECTION BAG 22-3/4" X 30"
BAG CLAMP
6
BUSHING
7
PHLP HD SCR M5-.8 X 10
SET SCREW 1/4-20 X 5/16
COLLECTION FLANGE
CONNECTION COLLAR
CLEANOUT FLAPPER
FLAT WASHER 1/4
SPINDLE BRACKET
BEARING PLATE
FLANGE SCREW 1/4-20 X 3/4
HEX BOLT 5/16-18 X 2
FLAT WASHER 5/16
8
9
10
11
12
13
14
15
16
17
HEX NUT 5/16-18
HEX NUT M5-.8
GASKET (RUBBER)
PHLP HD SCR M5-.8 X 8
FLANGE SEAL (FOAM)
FILTER SEAL (FOAM)
WRENCH 10 X 12MM OPEN-ENDS
FLANGE GASKET (FOAM)
PHLP HD SCR M6-1 X 12
MOUNTING PLATE
PHLP HD SCR M5-.8 X 10
Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here
are available for purchase. Call (800) 523-4777 or visit our online parts store at www.grizzly.com to check for availability.
-4-
Model T10877 (Mfd. 03/15)
|