EdgeStar Ice Maker IP300P User Manual

 
TABLE OF CONTENTS  
IMPORTANT SAFETY INSTRUCTIONS…………………………………………………1  
PREPARING YOUR ICE MAKER FOR USE  
IMPORTANT SAFETY TIPS.……………………………………………………………….2  
GETTING TO KNOW YOUR UNIT………………………………………………………..3  
OPERATING PROCEDURES & MAINTENANCE  
UNPACKING YOUR ICE MAKER ..………….…………………………………………...4  
CONNECTING YOUR ICE MAKER……………….……….……………………………..4  
CLEANING AND MAINTAINING YOUR ICE MAKER….……………………………….4  
USING YOUR ICE MAKER……………….……..………………………………………...5  
TROUBLESHOOTING...……………………….……………………………………………6  
TECHNICAL SPECIFICATIONS & CIRCUIT DIAGRAM…..……………..….………..7  
LIMITED WARRANTY…………………………………………..……………..….………..8  
 
Your safety and the safety of others is very important.  
We have provided many important safety messages in this manual and on your appliance.  
Always read and obey all safety messages.  
This is the safety alert symbol:  
!
All safety messages will follow the safety alert symbol and the word “DANGER” or  
“WARNING”.  
DANGER  
!
WARNING  
These words mean:  
You can be killed or seriously injured if you don’t immediately follow instructions.  
All safety messages will tell you what the potential hazard is, tell you how to reduce the  
chance of injury, and tell you what can happen if the instructions are not followed.  
1
 
PREPARING YOUR ICE MAKER FOR USE  
IMPORTANT SAFETY TIPS  
When using electrical appliances, basic safety precautions should be followed to reduce the  
risk of fire, electric shock, and/or injury to persons or property. Read all instructions before  
using any appliance.  
z
Do not operate this or any other appliance with a damaged cord.  
Connect to properly polarized outlets only. No other appliance should be plugged into the  
same outlet. Be sure that the plug is fully inserted into the receptacle.  
z
z
Do not run cord over carpeting or other heat insulators. Do not cover the cord. Keep cord  
away from traffic areas, and do not submerge in water.  
We do not recommend the use of an extension cord, as it may overheat and become a  
fire risk. If you must use an extension cord, use a cord of No.14 AWG minimum size and  
rated for no less than 1875 watts.  
z
z
z
Unplug the ice maker before cleaning it or making repairs.  
Exercise caution and use reasonable supervision when appliance is used near children.  
Do not clean your ice maker with flammable fluids. The fumes can create a fire hazard or  
explosion.  
z
z
z
Do not tip over.  
Do not operate with side or back panels removed.  
If the ice maker is brought in from outside in wintertime, give it a few hours to warm up to  
room temperature before plugging it in.  
2
 
GETTING TO KNOW YOUR UNIT  
3
 
OPERATING PROCEDURES & MAINTENANCE  
UNPACKING YOUR ICE MAKER  
1. Remove the exterior and interior packaging. Check that ice basket and ice scoop are  
included. If any parts are missing, please contact the vendor.  
2. Clean the interior with lukewarm water and a soft cloth. Take out the ice basket and clean  
it.  
3. Find a location for your ice maker that is protected from direct sunlight and other sources  
of heat (i.e., stove, furnace, radiator). Place the ice maker on a level surface. Maker sure  
that there is at least 5 inches of space between the back and sides of your ice maker and  
the wall.  
4. Allow one hour for the refrigerant to settle before plugging ice maker in.  
5. The appliance must be positioned so that the plug is accessible.  
CONNECTING YOUR ICE MAKER  
DANGER  
!
* Improper use of the grounded plug can result in the risk of electrical shock. If the  
power cord is damaged please call service.  
1. This unit should be properly grounded for your safety. The power cord of this appliance is  
equipped with a three-prong plug which mates with standard three prong wall outlets to  
minimize the possibility of electric shock.  
2. Plug your appliance into an exclusive, properly installed, grounded wall outlet. Do not  
under any circumstances cut or remove the third (ground) prong from the power cord. Any  
questions concerning power and/or grounding should be directed toward a certified  
electrician.  
3. This appliance requires a standard 110~120 volt, 60Hz electrical outlet with three-prong  
ground.  
CLEANING AND MAINTAINING YOUR ICE MAKER  
Before using your ice maker, you are strongly recommended to clean it thoroughly.  
1. Take out the ice basket.  
2. Clean the interior with diluted detergent, warm water and a soft cloth.  
3. The outside of the ice maker should be cleaned regularly with a mild detergent solution  
and warm water.  
4. Dry the interior and exterior with a soft cloth.  
5. When the machine is not in use, open the water drain cap to completely drain the water  
reservoir.  
4
 
USING YOUR ICE MAKER  
1. Select the size of the ice cube by pressing the “Size” button. If the room temperature is  
lower than 60°F, it is best to select the small or medium ice size, otherwise the ice cubes  
might stick together.  
2. Open the cover, remove the ice basket and pour water into tank.  
Keep water level below the “Fill Line”.  
3. Press “On” on the control panel to begin the ice making cycle.  
4. The ice making cycle lasts 7 to 15 minutes, depending on the size of the ice cubes  
selected.  
5. While the ice maker is on, verify the water level periodically. If the water level is too low,  
the ice maker will stop automatically, and the “Add Water” indicator will turn on.  
Press the “Off” button, fill the unit with water, and then press the “On” button.  
Allow the refrigerant inside the compressor at least 3 minutes to settle before restarting.  
6. The ice maker automatically stops working when the ice basket is full.  
7. If you fill the unit with water, but the ice maker still does not function, empty some water  
out through the drain, then recap the drain. The machine should start automatically.  
8. Change the water in the water reservoir periodically to ensure cleanliness and hygiene.  
9. It is best to use tap water or bottled drinking water in the ice maker. Distilled water may not  
work. If you do use distilled water and the ice maker will not function, try adding a little salt  
into the water (a small amount of salt added to the water should be imperceptible).  
10. If the ice does not taste good, or the unit develops a musty odor, try running a few cycles  
of the ice maker with a mild white vinegar solution. Then empty out all the vinegar solution  
and run a few cycles with plain water to eliminate all traces of the vinegar.  
If the ice maker will not be used for an extended period of time, you should drain the water  
from the reservoir.  
5
 
TROUBLESHOOTING  
PROBLEM  
POSSIBLE CAUSE  
SOLUTION  
Stop the ice maker, fill it with water,  
Low water level.  
and then restart it.  
Open the drain cap on the back of  
the unit and drain out a small  
amount of water. Replace the drain  
cap and attempt to use the unit  
again.  
There is some air in the  
lines.  
The “Add Water”  
indicator is on.  
The unit is filled with Add a little bit of salt to the water or  
distilled water- or some use water from a different source  
other type of water with (tap water or bottled drinking water  
no impurities.  
is best).  
The “Ice Full”  
indicator is on.  
The ice basket is full.  
Remove ice from the ice basket.  
The “Water” and  
“Ice” indicators  
are both flashing.  
The ice pusher cannot Check if the ice is blocking the ice  
move.  
pusher, otherwise, consult service.  
Stop the ice maker, and restart it  
The ice cycle is too long. when the ice blocks melt. Select  
the small ice button.  
The ice cubes  
stick together.  
Change the water in the inner tank.  
The water temperature in  
The ideal water temperature is  
the inner tank is too low.  
45°-90°F.  
The unit is being run off  
Plug the unit into a 110/120 Volt,  
the wrong voltage or  
60 Hertz power source.  
frequency.  
The compressor  
makes a loud  
buzzing noise  
The compressor was  
Contact the shipper.  
damaged in shipping.  
Power is not supplied to Plug the unit into a 110/120 Volt,  
The unit does  
nothing  
the unit.  
60 Hertz power source.  
The ambient temperature Please run the ice maker in  
or the water temperature temperatures below 90°F and/or  
The ice making  
is too high.  
pour colder water into tank.  
cycle  
seems  
normal but no ice  
is produced.  
Refrigerant leakage.  
A pipe in the cooling  
system is blocked.  
Consult a qualified technician.  
Consult a qualified technician.  
6
 
TECHNICAL SPECIFICATIONS & CIRCUIT DIAGRAM  
TECHNICAL SPECIFICATIONS  
Model  
IP300P  
Climate Type  
Protection Class  
Power  
N
I
110V~120V/60Hz  
3.5 A  
Rated Current  
Power Input  
Refrigerant  
150W  
R134a/3oz  
12InX15InX15In  
Size (HXWXD)  
CIRCUIT DIAGRAM  
7
 

Exmark Lawn Mower Lazer ZCT User Manual
Extron electronic Power Supply VSC 100 User Manual
Fellowes Paper Shredder HS 800 User Manual
Frigidaire Ventilation Hood PLHV42P8KC User Manual
Fujitsu Power Supply MB3878 User Manual
Fujitsu Printer FTP 632MCL001 User Manual
FUNAI DVD VCR Combo DV220TT8 User Manual
GBC Binding Machine P70IX User Manual
GE Cooktop 164D2966P161 1 User Manual
Gigabyte Network Card GA 8I915MD GV User Manual