Hitachi Travelstar HTS725032A9A364 User Manual

Quick Installation Guide  
Hitachi Travelstar 7K500  
Models: HTS725050A9A364  
HTS725040A9A364  
HTS725032A9A364  
HTS725025A9A364  
HTS725016A9A364  
HTS725012A9A364  
HTS725050A9A361  
HTS725040A9A361  
HTS725032A9A361  
HTS725025A9A361  
HTS725016A9A361  
HTS725012A9A361  
HTS725050A9A360  
HTS725040A9A360  
HTS725032A9A360  
HTS725025A9A360  
HTS725016A9A360  
HTS725012A9A360  
HTE725050A9A364  
HTE725040A9A364  
HTE725032A9A364  
HTE725025A9A364  
HTE725016A9A364  
HTS725050A9A362  
HTS725040A9A362  
HTS725032A9A362  
HTS725025A9A362  
HTS725016A9A362  
HTS725012A9A362  
Handling precautions  
ƒ Set the drive down gently to prevent damage from impact or vibration.  
ƒ Handle the drive carefully by the edges. Do not touch the exposed printed circuit board or any electronic components.  
ƒ Do not press on the top or bottom of the drive.  
ƒ Before handling the drive, discharge any static electricity from yourself and your clothing. With one hand touch an  
unpainted metal surface, then touch the ESD bag with the other hand. Remain in contact with the chassis and the bag  
for a minimum of two seconds.  
ƒ Vibration, shock and static electricity to the drive will damage the precision parts. In particular, prevent vibration or  
shock generated by dropping, knocking over or hitting the drive. Also, avoid touching the electrical components  
directly, which can discharge electrostatic energy and damage the drive.  
Page 1  
version 1.0  
Hitachi Global Storage Technologies  
The drive will operate in all axes (six directions) and will stay within the specified error  
rates when tilted ±5 degrees from these positions. Performance and error rate will stay  
within specification limits if the drive is operated in the other permissible orientations from  
which it was formatted. Thus a drive formatted in a horizontal orientation will be able to  
run vertically and vice versa.  
The recommended mounting screw torque is 0.3±0.05 Nm.  
The recommended mounting screw depth is 3.0±0.3 mm for bottom and 3.5±0.5 mm for  
horizontal mounting.  
The user is responsible for using the appropriate screws or equivalent mounting hardware  
to mount the drive securely enough to prevent excessive motion or vibration of the drive at  
seek operation or spindle rotation.  
Page 3  
version 1.0  
Hitachi Global Storage Technologies  
Interface connector  
The figure below shows the physical pin location  
ƒ All pins are in a single row, with a 127 mm (0.050”) pitch.  
ƒ The comments on the mating sequence in Table in the section 7.3 apply to the case of  
back-plane  
ƒ blind-mate connector only. In this case, the mating sequences are:(1)the ground pins  
P4 and P12;(2) the pre-charge power pins and the other ground pins; and (3) the  
signal pins and the rest of the power pins.  
ƒ There are three power pins for each voltage. One pin from each voltage is used for  
pre-charge in the backplane blind-mate situation.  
ƒ If a device uses 3.3V, then all V33 pins must be terminated. Otherwise, it is optional  
to terminate any of the V33 pins  
ƒ If a device uses 5.0V, then all V5 pins must be terminated. Otherwise, it is optional to  
terminate any of the V5 pins  
ƒ If a device uses 12.0V, then all V12 pins must be terminated. Otherwise, it is optional  
to terminate any of the V12 pins.  
Page 4  
version 1.0  
Hitachi Global Storage Technologies  
© 2009 Hitachi Global Storage Technologies  
Produced in the United States 6/09  
All rights reserved  
Travelstar is a trademark of Hitachi Global Storage  
Technologies.  
Hitachi Global Storage Technologies’ trademarks are  
authorized for use in countries and jurisdictions in which  
Hitachi has the right to use, market and advertise the brands.  
The Travelstar trademark is authorized for use in the Americas,  
EMEA and the following Asia-Pacific countries and  
jurisdictions: Australia, Hong Kong, Japan, New Zealand,  
South Korea and Taiwan. Contact Hitachi for further  
information. Hitachi Global Storage Technologies shall not be  
liable to third parties for unauthorized use of Hitachi Global  
Storage Technologies trademarks.  
References in this publication to Hitachi Global Storage  
Technologies’ products, programs, or services do not imply  
that Hitachi intends to make these available in all countries in  
which it operates. Some countries have laws that may affect  
encryption-enabled devices. Hitachi GST assumes no  
responsibility for compliance with laws that apply to our  
products after they are sold or outside of our control.  
Accordingly, we suggest that you review all laws of the  
countries where you conduct business.  
Product specifications provided are sample specifications and  
do not constitute a warranty. Information is true as of the date  
of publication and is subject to change. Actual specifications  
for unique part numbers may vary. Please visit the Support  
additional information on product specifications. Photographs  
may show design models.  
24 June 2009  
Page 5  
version 1.0  

NEC Electronics America Cell Phone DSX 80 User Manual
Mr Coffee CK24 User Manual
Kyocera Topaz 901 User Manual
Krups Coffeemaker XP2010 User Manual
Kompernass KH 2190 User Manual
HTC Pocket PC Phone User Manual
HP Hewlett Packard Hewlett Packard Computer Drive D2D2504 G2 User Manual
GE 681131691840 User Manual
Emerson Computer Accessories MVME2500 User Manual
Bose PM 1 User Manual