Vizio Universal Remote P265V1 User Manual

Thank you for subscribing to  
FiOS TV Service. This User  
Manual will show you how to  
program and operate your  
new FiOS TV Remote Control  
(Model P265v1).  
5. Press and release the  
<CH +> button repeatedly  
until the TV turns off. You  
can also “back up” by  
FiOS TV Remote Control  
Codes for Major TV Brands  
8) Troubleshooting  
a. If the button does not  
work correctly, make sure  
will blink each time a new  
code is sent.  
6. When the TV turns off, stop  
pressing the play button right  
away.  
• Please note – some TVs  
may respond slower than  
others.  
7. You can press the <CH +>  
or <CH -> buttons to go  
forward or back one TV code  
at a time.  
e. Once you have tried all the  
TV codes in the remote  
control, the RED LED and  
the backlit buttons will flash  
4 times rapidly, the RED  
LED will turn off and the  
remote will exit the  
4. The RED LED light will  
blink twice, and remain on.  
2. Your FiOS TV remote  
control will only operate your  
FiOS TV STB and your TV.  
3. The remote will not operate  
other devices like DVD  
2.  
3.  
“Widgets” displays local  
weather, traffic, and other  
information.  
displays your list of  
recorded programs if you  
have DVR service.  
“Favorites” displays your  
list of favorite channels.  
is a rocker button.  
Verizon FiOS TV  
P265v1 Remote  
Control Manual  
TV Brand  
AOC  
Code  
5. Press  
.
026  
035  
070  
114  
128  
146  
164  
180  
193  
210  
222  
243  
279  
285  
290  
294  
302  
321  
331  
332  
333  
335  
342  
352  
371  
397  
418  
424  
433  
440  
the TV is on and go back to  
Step 1 of the Quick Start  
Guide. You can also try the  
Code Search Method  
below.  
6. The RED LED will blink 3  
times and then turn off.  
7. If you want to change it back  
pressing the <CH -> button.  
Audiovox  
Coby  
Envision  
Funai  
Player or Audio Receiver.  
again so that volume buttons 4. The <TV Power>,<VOL +>,  
control the TV follow the  
same steps as above but  
4.  
5.  
Quick Setup Guide-Verizon  
FiOS remote  
programming mode.  
<VOL ->, <Mute> and  
<A/V> buttons will always  
control your TV.  
Haier  
b. If the <VOL>, <Mute>, or  
<A/V> buttons do not work  
correctly, please refer to the  
Key Fix Feature.  
c. If you think you made a  
mistake with programming  
f. If you are still having  
problems programming the  
remote, please refer to our  
website at  
Hitachi  
Insignia  
JVC  
press  
in Step 5.  
Press lower half of  
5. All other keys on the remote  
control will always control  
your FiOS TV STB.  
the button  
to  
The following steps will guide  
you to quickly set -up your  
Verizon FiOS TV remote for  
your TV.  
*Please note – some TVs may  
respond slower than others.  
Please allow 1 second  
Key Fix  
LG  
8. Test that the remote control  
is programmed for your TV.  
If your remote control is  
programmed for your TV, but  
the <VOL>, <Mute>, or the  
<A/V> keys do not work  
correctly, then you can try  
using the Key Fix feature to fix  
the buttons.  
pause the program. Press  
upper half of the button  
<►> to continue to play  
from where you left off.  
jumps back 30  
seconds in the program you  
are watching.  
jumps forward 30  
seconds in the program you  
are watching.  
Magnavox  
Mitsubishi  
Panasonic  
Philips  
between button presses.  
your remote, you can always a. Turn the TV on using the  
OPTIONAL FEATURES  
<STB Power> Button Turns  
Getting Started  
press the <Exit> button and  
start over. The RED LED  
will turn off if the RC is not  
in programming mode.  
d. If you don’t press any  
buttons for 60 seconds, the  
remote control will  
automatically exit  
programming mode.  
e. Note, if you press the <CH>  
button many times. and the  
lights on the remote control  
all flash rapidly, the  
key.  
1. Turn on your TV and the  
FiOS STB. Make sure you  
can see live television.  
6. Test that remote control is  
programmed for your TV  
a. Turn the TV on using the  
key.  
b. Press <VOL +> and  
<VOL -> to make sure that  
the volume keys work.  
b. Press <VOL +> and <VOL -> on TV and STB  
1. Turn on your TV and the  
6.  
7.  
8.  
Pioneer  
Polaroid  
Proscan  
RCA  
to make sure that the volume Your remote has separate  
STB using the  
buttons.  
and  
keys work.  
c. Press  
d. If any of these keys do not  
power buttons for the TV and  
STB. You can program the  
key to turn on/off both  
and  
.
2. If you have just watched a  
DVD, make sure your TV is  
set to the correct A/V Input  
for your STB.  
1. Press and hold the <OK>  
Samsung  
Sansui  
Sanyo  
Sceptre  
Sharp  
work as expected, press and your TV and STB at the same  
hold that key. Release it as  
soon as it works.  
and  
buttons  
time.  
simultaneously.  
records the current  
program.  
c. Press  
and  
keys.  
• The Red LED will blink twice 3. Press the <CH +>,or <CH ->  
d. If any of these keys do not  
work as expected, press  
and hold that key. Release  
it as soon as it works.  
9. If these keys all work, press  
<OK> to save this TV brand  
1. Turn both your TV and STB  
and then stay on.  
buttons to see the next  
higher or lower channel.  
4. You can go directly to any  
channel by entering the  
channel number on the  
numberpad and pressing  
<OK>.  
9. Buttons  
,
, and  
2. Locate the 3-digit code for  
your TV brand in the list  
below and circle the correct  
code.  
on.  
2. Press and hold the key that  
does not work correctly.The  
remote control will try a new  
code every second.  
3. Once the TV responds  
correctly, release the button.  
4. Press <OK> to save the  
current settings and finish  
programming your remote  
control.  
will only operate  
during normal TV watching  
if you have DVR service.  
10. “If the RED LED starts  
blinking 5 times rapidly  
when you press the  
Sony  
code programming. The RED 2. Press and hold the <OK>  
LED will blink 3 times and  
then turn off.  
Sylvania  
Toshiba  
Viewsonic  
Vizio  
and  
buttons together,  
programming attempt was  
not successful.  
f. If the Brand Search method  
then release both.  
• The RED LED will blink  
twice and then stay on.  
3. Press 9 7 7.  
• The Red LED will blink  
twice and remain on.  
Shortlist  
Brands  
Your Remote Control is now  
of  
brands  
Code  
Westinghouse  
Zenith  
does not work, please try the programmed for your TV!  
Code Search Method below,  
5. Press  
to see a list of  
<CH +/->, <CH +/->, and  
<OK>, or if the buttons  
stop lighting up, you should  
replace the remote control  
batteries”  
TV programs.  
which scans the complete  
database for all TV codes.  
g. If you are still having  
problems programming the  
remote, please refer to our  
website at  
10.Troubleshooting  
a. If the button does not  
work correctly, make sure  
6. Press  
to return to TV  
7. If all these keys work, press  
<OK> to save this TV brand  
code programming. The  
RED LED will blink 3 times  
and then turn off  
4. Press  
.
If your TV brand is not listed,  
codes for additional TV  
brands are listed at the back  
of this manual.  
• The RED LED will blink 3  
watching.  
7. Press the  
the TV is on and go back  
to Step 1 of the Code  
Search Method.  
times and then turn off.  
Reset the Remote Control  
Original Settings  
button to  
5. Test that the  
key  
launch the FiOS TV Main  
Menu. From the Main Menu  
you can access all the  
features of your FiOS TV  
service.  
now turns on the TV and  
STB at the same time.  
6. If you want to reset the  
b. If the <VOL>, <Mute>, or  
<A/V>, buttons do not work  
correctly, please refer to the  
Key Fix Feature.  
c. If you think you made a  
mistake with programming  
your remote, you can  
1. Press and hold the <OK>  
3. Once you locate the brand  
code, press and hold the  
and  
buttons together,  
remote so that the  
controls Only the STB,  
follow the same steps as  
above but press <OK> in  
Step 4.  
key  
and release.  
<OK> and  
keys  
Code Search Method to  
Program the RC  
(This method could take up to  
8 minutes)  
2. The RED LED will blink  
twice and then stay on.  
3. Press 9 - 0 0.  
4. The RED LED will blink 3  
times and then turn off to  
indicate original settings are  
restored.  
5. CAUTION, all previous  
programming in the remote  
control will be lost if you  
follow this procedure.  
8. Press <▲> <▼> <►> <◄>  
keys to navigate through the  
FiOS TV Menus and Guides.  
To select any item, press  
<OK>.  
together. The RED LED on  
the remote control will blink  
twice and then stay on.  
Your Remote Control is now  
programmed for your TV!  
5-sec.  
always press the <Exit>  
button and start over. The  
RED LED will turn off if the  
RC is not in programming  
mode.  
Model: RC2655001/01B  
1. Turn on your TV and the  
FiOS STB.  
2. Make sure you can see live  
television.  
Control TV Volume  
Through STB  
9. Press  
to return to the  
Acronyms  
last channel.  
For additional information  
about your FiOS TV service  
and your remote, go to  
1. RC = Remote Control  
2. STB = FiOS TV Set Top  
Box  
3. VOL = Volume  
4. CH+ = Channel Up  
5. CH- = Channel Down  
If the volume control keys  
don’t work with your TV, you  
can program the remote so  
that the STB will control the  
volume.  
10. Press <Info> to see  
information about the  
current program.  
11. Press <Exit> to return to  
the previous menu option  
or to watch TV.  
3. Press and hold the <OK>  
d. Please Note, the Code  
Search Method could take  
up to 8 minutes, as it must  
go through over 500 codes.  
The most common codes  
are tried first, but you may  
need to press and  
4. Enter the 3-digit TV code  
for your TV brand using the  
number pad. The RED  
LED will blink twice and  
then stay on.  
and  
buttons together,  
then release both.  
For video instructions, press  
the <Menu> key on your  
remote then select Help on  
the Main Menu  
• The RED LED will blink twice  
and then stay on.  
4. Press and hold down the  
button.  
General Instructions  
1. Press and hold the <OK>  
and  
buttons together,  
1. Make sure the remote  
control has a clear,  
unobstructed view of the  
STB and TV.  
New and Special Buttons  
then release both.  
2. The RED LED will blink  
twice and then stay on.  
3. Press 9 - 5 5.  
hold  
for a while to  
1.  
“On Demand” displays  
a list of movies and other  
programs you can watch at  
any time.  
5. The Remote Control will try  
a new TV code every  
locate the correct code.  
second, and the RED LED  
 

Targus Network Card USB to Serial Digital Device Adapter User Manual
THORENS Turntable TD 2010 User Manual
Toshiba Network Card SD M2012C User Manual
TRENDnet Network Router TEW 430APB c1 User Manual
Tripp Lite Switch B054 001 PS2 User Manual
Ultra Products Personal Computer ULT31418 User Manual
ViewSonic MP3 Player VS13482 User Manual
Vizio Car Satellite TV System M321i A2 User Manual
Vizio Music Mixer S4221w C4 User Manual
VTech Cordless Telephone CS6519 User Manual