Metra Electronics Automobile Accessories 95 7418 User Manual

INSTALLATION INSTRUCTIONS FOR PART 95-7418  
APPLICATIONS  
2002-2004 Nissan Altima  
95-7418  
KIT FEATURES  
• DDIN Head Unit Provision  
• STACKED ISO DIN Head Unit Provision  
KIT COMPONENTS  
A) Trim Plate  
A
TOOLS REQUIRED:  
Flat Blade Screwdriver I Phillips Screwdriver  
1-800-221-0932  
© COPYRIGHT 2004 METRA ELECTRONICS CORPORATION  
 
DASH DISASSEMBLY  
2002-2004 NISSAN ALTIMA  
95-7418  
Disconnect the negative battery  
terminal to prevent an accidental  
short circuit.  
1
2
3
A
Unclip and remove the trim panel  
surrounding the climate controls.  
(Figure A)  
Remove (1) Phillips screw (bottom  
right side of panel) securing the  
panel surrounding the radio then  
unclip and remove the panel.  
(Figure B,C)  
Remove (4) Phillips screws securing  
radio to remove. (Figure D)  
4
5
B
Remove the screws securing the  
factory brackets to the radio and  
remove brackets. (Retain brackets  
for re-use during kit assembly.)  
D
C
1
 
KIT ASSEMBLY  
95-7418  
DOUBLE DIN HEAD UNIT PROVISION  
Snap the 95-7418 trim plate into the  
1
radio trim panel. (Figure A)  
A
Install from rear  
Slide the DDIN radio unit into the  
2
factory brackets and secure the unit  
to the brackets using the screws  
supplied with the head unit. (Figure  
B)  
B
2
 
KIT ASSEMBLY  
95-7418  
STACKED ISO DIN HEAD UNIT PROVISION  
Snap the 95-7418 trim plate into the  
radio trim panel. (Figure A)  
1
A
Install from rear  
Slide the stacked ISO DIN units into  
the factory brackets and secure the  
units to the brackets using the  
screws supplied with the head unit.  
(Figure B)  
2
B
3
 
FINAL ASSEMBLY  
95-7418  
FINAL ASSEMBLY  
Locate the factory wiring harness in the dash and make the connection as shown.  
Metra recomends using the proper mating adapter and making the connections as  
shown. (Isolate and individually tape off the ends of any unused wires to prevent  
electrical short circuit.)  
1
Re-connect the negative battery terminal and test the unit for proper operation.  
Reassemble radio and dash assemblies in reverse order of disassembly.  
2
3
FINAL WIRING CONNECTIONS  
Make wiring connections using the EIA color code chart shown below and the instructions included with the head  
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually  
tape off ends of any unused wires to prevent electrical short circuit.  
A
A)  
B)  
C)  
D)  
Strip wire ends back 1/2"  
Twist ends together  
Solder  
B
C
D
Tape  
METRA / EIA WIRING CODE  
12V Ignition / Acc . . . Red  
Right Front (+) . . . . . Gray  
12V Batt / Memory . . Yellow  
Ground . . . . . . . . . . . Black*  
Power Antenna . . . . . Blue  
Right Front (-). . . . . . Gray / Black  
Left Front (+) . . . . . . White  
Left Front (-). . . . . . . White / Black  
Right Rear (+). . . . . . Violet  
Amp Turn-On . . . . . . Blue / White  
Amp Ground . . . . . . . Black / White  
Illumination. . . . . . . . Orange  
Dimmer . . . . . . . . . . Orange / White  
Right Rear (-) . . . . . . Violet / Black  
Left Rear (+). . . . . . . Green  
Left Rear (-) . . . . . . . Green / Black  
*NOTE: When Black a wire is not present, ground radio to vehicle chassis.  
All colors may not be present on all leads due to manufacturer’s specifications.  
4
 
95-7418  
NOTES  
5
 
95-7418 INSTRUCTIONS  
1-800-221-0932  
© COPYRIGHT 2004 METRA ELECTRONICS CORPORATION  
INST95-7418  
REV. 09/06/07  
 

La Pavoni Food Processor LP25 User Manual
Leica Laser Level 776748 User Manual
Leisure Time Telescope LX20 User Manual
Lenmar Enterprises Battery Charger PRO32A User Manual
LG Electronics Refrigerator LRSC21935 User Manual
Lincoln Welder ML 2 User Manual
Loewe Flat Panel Television L 26 User Manual
Makita Drill 8414D User Manual
Manley Labs Stereo Amplifier STUDIO STANDARD 350 WATT MONOBLOCK AMPLIFIER User Manual
Maretron Marine Instruments DSM250 01 User Manual