Linear Satellite Radio DXS 31 User Manual

DXS-31 FEATURES & ACCESSORIES  
DXS-31  
TRANSMITTER  
DXS-31  
1/2" GAP DISTANCE  
MAXIMUM  
DXS  
FORMAT  
By  
SUPERVISED  
DOOR/WINDOW  
TRANSMITTER  
TRANSMITTER  
SCREWS AND  
DOUBLE STICK TAPE  
MAGNET CAN BE MOUNTED UP TO  
1/2" FROM LEFT SIDE OF  
TRANSMITTER  
Installation Instructions  
ADJUSTABLE  
MAGNET  
MAGNET  
ADJUSTMENT  
TAB (EACH SIDE)  
MAGNET  
SCREWS AND  
DOUBLE STICK TAPE  
(760) 438-7000 FAX (760) 438-7043  
USA & Canada (800) 421-1587 & (800) 392-0123  
Toll Free FAX (800) 468-1340  
SQUEEZE MAGNET TABS TO  
ADJUST MAGNET HEIGHT (4 POSITIONS)  
PRODUCT DESCRIPTION  
The DXS-31 is a battery powered stationary transmitter designed for use with Linear’s DXS and DX The transmitter is powered from two 3-Volt #2032 lithium batteries with an expected battery life of  
format receivers. This transmitter can be used in a variety of wireless remote control applications. up to 3 years.  
Triggering the transmitter with its built-in magnetic switch, an external switch or an external glass  
break detector sends a digitally coded wireless signal to its companion receiver.  
Every hour, the DXS-31 will send a status transmission to the receiver. The hourly signal updates  
the receiver to the transmitters condition. By monitoring status transmissions, the receiver can  
The digital DXS code format features over a million possible codes. The DXS transmitters are determine if a transmitter has a low battery or has been removed from the system. DXS format  
precoded at the factory to unique codes, so no field coding is required. The DXS-31 can send four receivers can monitor status signals, DX format receivers cannot.  
different codes: alarm, restore, low battery and status.  
A three-position terminal block is for connection to normally closed external contacts or a normally  
For versatility, any transmitter can be programmed into any receiver channel. Receivers must be open Window Bugtype glass break sensor. An internal jumper selects which input to use.  
programmed to the transmitters code before system testing and operation. Refer to the receivers Selections are: internal switch only, external switch only, both external and internal switch, and glass  
instructions for details on programming.  
break sensor.  
In a typical installation, the magnet is mounted on a door or window and the transmitter is mounted Another internal jumper selects an instant or delayed transmission code. This jumper doesnt delay  
on the frame. When the magnet moves more than 1/2" away from the transmitter, an alarm signal the actual transmissions, but changes the code of the signal sent so the receiver can process the  
is sent. When the magnet returns next to the unit, a restore signal is sent. Alarms and restores can signal as coming from an entry/exit delay transmitter.  
also be sent from external contacts wired to the terminal block. Pressing the case sends a test  
transmission that updates the receiver to the current state of the contacts and lights the test indicator.  
A snap-on transmitter mounting plate is provided for easy installation. The magnet is adjustable with  
four height positions. A 1/4" high magnet spacer is also supplied to snap on to the base of the magnet.  
When the transmitters case is open, the transmit indicator will light each time the unit sends an  
alarm or restore signal. The indicator is disabled when the case is closed (except for test  
transmissions). The indicator will flash during operation and test when the batteries are low.  
OPENING CASE  
REMOVE BATTERY PROTECTION STRIP  
REMOVE THE CASE TOP BY TWISTING A  
SMALL FLAT BLADE SCREWDRIVER IN THE  
TOP CASE SLOT (ON THE FAT END OF THE  
TRANSMITTER)  
PULL  
STRIP TO  
REMOVE  
BATTERY  
PROTECTION  
STRIP  
LIFT  
TWIST  
COMPONENT LOCATIONS  
EXAMPLE INSTALLATIONS  
LEFT OPENING DOOR  
TRANSMITTER  
SLIDING WINDOW  
INSTANT/DELAY  
OPTION JUMPER  
ANTENNA  
MOUNTED ON  
DOOR JAMB  
MAGNET  
ALIGNMENT  
MARK  
MAGNET MOUNTED  
ON WINDOW FRAME  
INPUT  
SELECT  
TWO TYPE 2032  
BATTERIES  
(NOTE: SMALL END  
JUMPER  
OF TRANSMITTER UP)  
BATTERY  
CLAMP  
SCREW  
MAGNET  
MOUNTED  
ON DOOR  
TRANSMIT  
TRANSMITTER  
MOUNTED ON  
WINDOW SILL  
INDICATOR  
RIGHT OPENING DOOR  
DOUBLE-HUNG  
WINDOW  
BATTERY CLAMP  
TRANSMITTER  
MOUNTED ON  
WINDOW FRAME  
TRANSMITTER  
MOUNTED ON  
DOOR JAMB  
TEST  
SWITCH  
(NOTE: SMALL END  
OF TRANSMITTER DOWN)  
EXTERNAL  
INPUT  
MAGNET  
MOUNTED  
ON WINDOW  
SASH STILE  
MAGNET MOUNTED  
ON DOOR  
TERMINALS  
 

Lexmark Printer 22W0310 User Manual
Life Fitness Home Gym SU05 User Manual
Linear Stereo Receiver RV5060 User Manual
Lowrance electronic Radio LVR 250 User Manual
LST Network Card GWM 55000 845 User Manual
M 2GR45MF 2GR65MR 2GR85MF 3GR45MF 3GR65MF 3GR85MF 4GR45MF ML 136407 ML 136408 ML 136409 ML 136410 ML 136417 ML 136418 ML 136419 ML 136420 ML 136421 ML 136422 ML 136423 User Manual
Magnadyne DVD Player MV DVD PL8 User Manual
Manitowoc Ice Ice Maker K00370 User Manual
Maytag Refrigerator M8RXEGMAB User Manual
Mercedes Benz Automobile 2003 C 230 Kompressor Sport User Manual