LevelOne Switch KVM 0213 User Manual

LevelOne  
User Manual  
KVM-0213  
2-Port PS/2 Cable KVM Switch  
Ver. 1.0.0-0803  
 
Installation  
Important  
1. Before you begin, make sure that the power to all the devices you will be connecting has  
been turned off. You must unplug the power cords of any computers that have the  
Keyboard Power On function. Otherwise, the switch will receive power from the computer.  
2. To prevent damage to your equipment, make sure that all the devices you will be  
connecting are properly grounded.  
Installing your new KVM-0213 involves the following steps:  
1. Plug your keyboard, monitor, and mouse into the Console ports on the KVM-0213. Each  
port is labeled with an appropriate icon.  
2. Plug your speakers into the KVM-0213’s speaker jack. *This step is optional  
3. Plug the attached KVM cables’ keyboard, monitor, mouse, and speaker connectors into  
their respective ports on the computers you are installing.  
After you have finished attaching the cables, turn on the power to the computers.  
Note: The KVM-0213’s Power On default is to link to the first computer you turn on.  
Operation  
Hotkey Port Selection  
All hotkey port switches begin with tapping the Scroll Lock key twice.  
[Scroll Lock] [Scroll Lock]  
Invokes Auto Scan Mode  
Starts Auto Scan. Press and release the [Left Shift] key, and then press the [Right Shift] key.  
[Left Shift] [Right Shift]  
Scan Interval  
Sets the Auto Scan interval to n second intervals - where n is a number from 1 – 4.  
[Left shift] [Right shift] [S] [n]  
The n stands for the number of seconds that the focus dwells on a port  
before switching to the other one. Replace the n with a number  
between 1 and 4 when entering this hotkey combination. (See the  
table, below.)  
 
Scan Interval Table  
n
1
2
3
4
Sec.  
3 Sec.  
5 Sec. (Default)  
10 Sec.  
20 Sec.  
Troubleshooting  
Symptom  
Possible Cause  
Action  
Keyboard Not Responding  
Keyboard needs to be reset. Unplug the keyboard from  
the Console  
Keyboard Port, then plug it  
back in.  
Switch needs to be reset.  
Turn off the computers.  
Unplug the KVM cables. Wait  
five seconds; then plug the  
cables back in and turn the  
computers on.  
Pressing Hot Keys Gets No  
Response  
Hotkey sequence input  
incorrectly.  
Resend the Hotkey  
command – press and  
release each key in the  
sequence individually.  
Unplug the mouse from the  
Console  
Mouse Not Detected, or  
Mouse needs to be reset.  
Does Not Respond Correctly  
Mouse Port, then plug it back  
in.  
Video Problems  
Resolution and/or  
Select a lower resolution  
and/or bandwidth.  
Bandwidth set too high.  
 
Specifications  
Function  
Computer Connections  
Port Selection  
KVM-0213  
2
Hotkey  
Keyboard  
Video  
Mouse  
1 x 6-pin Mini-DIN Female (Purple)  
1 x HDB-15 Female (Blue)  
1 x 6-pin Mini-DIN Female (Green)  
1 x Mini Stereo Jack Female (Green)  
Console  
Ports  
Speaker  
Keyboard  
Video  
2 x 6-pin Mini-DIN Male (Purple)  
2 x HDB-15 Male (Blue)  
Connectors  
KVM  
Ports  
Mouse  
2 x 6-pin Mini-DIN Male (Green)  
Speaker  
2 x Mini Stereo Plug Male (Green)  
2 (Green)  
LEDs  
Selected  
Cable  
Length  
Computers  
1.2m  
Emulation  
Video  
Scan Interval  
Keyboard/ Mouse  
PS/2  
2048 x 1536; DDC2B  
3, 5, 10, 20 Seconds  
0-50°C  
Operating Temp.  
Storage Temp.  
Humidity  
Environment  
-20-60°C  
0-80% RH, Non-condensing  
Plastic  
Housing  
Weight  
0.41 kg  
Physical  
Properties  
Dimensions  
(L x W x H)  
8.1 x 6.3 x 2.35 cm  
 

LaCie Computer Drive Design By FA Porsche User Manual
Learning Resources Baby Toy LER 6226 User Manual
LevelOne Network Router WBR 3407 11g User Manual
Lindy Tablet Accessory 40592 User Manual
Listen Technologies Stereo System LA 116 User Manual
Logitech Computer Keyboard K300 User Manual
Marantz Car Stereo System SA 14S1 User Manual
MB QUART Speaker PCE210 User Manual
Meade Telescope 114ST EQ D User Manual
Midland Radio Car Stereo System 120 320 CHANNEL UHF HIGH BAND MOBILE User Manual