Legacy Car Audio Car Stereo System LCD87DFX User Manual

TROUBLE SHOOTING  
Before going through the check list, check wiring connection.If any of the problems  
persist after check list has been made, consult your nearest service dealer.  
Symptom  
No power.  
Cause  
Solution  
If the power supply is properly  
connected to the car accessory  
terminal,switch the ignition key  
The car ignition switch is  
not on.  
to " CC"  
A
OWNER's MANUAL  
The fuse is blown.  
Replace the fuse.  
Mobile Video System  
Remove the disc in the player,  
Then put a new one  
Presence of disc inside the  
player.  
Disc cannot be  
loaded or ejected.  
Inserting the disc in reverse  
direction.  
Insert the compact disc with  
the label facing upward.  
The disc is extremely dirty or  
defective.  
Clean the disc or try to play a  
new one.  
Temperature inside the car  
is too high.  
Cool off or until the ambient  
temperature return to normal.  
Leave the player off for an hour  
then try again.  
Condensation.  
Adjust volume to a desired level.  
No sound.  
Volume is in minimum.  
Check wiring connection.  
Wiring is not properly  
connected.  
Adjust the installation angle less  
than 30 degrees.  
Sound skips.  
The installation angle is  
more than 30 degrees.  
The disc is extremely dirty  
or defective disc.  
Clean the compact disc, then  
try to play a new one.  
The operation keys  
do not work.  
Press the RESET button.  
Front panel is not properly fixed  
into its place.  
The built-in microcomputer  
is not operating properly  
due to noise.  
The radio does not  
work.  
The antenna cable is not  
connected.  
Insert the antenna cable firmly.  
Select a station manually.  
The signals are too weak.  
ANTI-THEFT FLIP DOWN DETACHABLE PANEL  
AUTO-LOADING COMPACT DISC PLAYER  
AM/FM/LW(OPTIONAL)-STEREO DIGITAL PLL TUNING RADIO  
WITH INFRARED REMOTE CONTROLLER  
WWW.Legacycaraudio.com  
11  
NOTES  
BASIC OPERATION  
DISC PLAY:  
Cleaning discs  
Before playing, clean the disc with a clean, lint-free.  
Flip the disc in the direction of the arrow.  
NOTE:  
.Do not use so solvents such as benzine, thinners. Commercially available  
cleaners or anti static spray damage the unit.  
Insert a disc with the label surface down. Doing so may damage the unit.  
NOTE:  
. Do not try to insert another disc when one has been already inserted.  
Doing so may damage the unit.  
Handle the disc by its edge. And to keep the disc clean, do not touch  
the surface.  
.Do not stick paper or tape on the disc.  
.Do not expose the disc to direct sunlight or heat sources such as hot air  
ducts. Or leave it in a car parked in direct sunlight where there can be a  
considerable rise in temperature.  
Label  
surface up  
Preparing the Remote Control  
Inserting the Batteries  
1.Open the battery compartment cover.  
2.Insert the new batteries. Make sure that the positive and negative terminals of the  
batteries are oriented indicated.  
3.Close the cover  
Using the Remote Control  
Face the remote control towards the player front face IR mark (remote control signal  
receiver).  
Operation angle: About +30 degree in each the direction of the front of the IR mark.  
9
2
BASIC OPERATION  
1. OPEN BUTTON  
INSTALLATION  
Press it to flip down the front panel then you can insert the cd disc into the cd compartment  
EJ button on the back of the front panel,press it to eject the disc.  
2.8.9 SEL( AUDIO MODE SELECT)/ +/- BUTTONS  
CAUTION: Do not install the detachable panel before connecting the wire.  
1. The unit is designed for negative terminal of the battery which is connected  
to the vehicle metal. Please confirm it before installation.  
Press SEL button to change the mode in the sequence of  
VOL  
(Volume)  
BAS  
(Bass)  
TRE  
(Treble)  
BAL  
(Balance)  
FAD  
(Fader)  
A.The volume level can be adjusted at any time by pressing the audio level+ or - button as  
select mode has been initially defaulted at volume mode.  
2. If the car interior is extremely hot, as after being parked in the sun, do not  
use the player until the car has been driven for a while to cool off the interior.  
The volume level is also obtained by stepping through the SEL button until the function  
VOL is displayed and then press + or - button to adjust the sound level.  
B.Press sel button to select the BAS,TRE ,BAL,FAD then press +/-button to adjust tthem.  
C.Press SEL button hold for more than 2 seconds and select + or - button can have a beep sound.  
3.10.TRACK UP /DOWN BUTTONS  
3. Press the OPEN button to flip down the front panel (see fig.1), then take  
away the front panel (see fig.2) and put it in the protective case (see fig.3)  
safe keeping.  
A. During CD mode, press  
button allow you to track forwards.  
4. Install the front panel back into its bracket and then push it back to the  
position for playing (see fig.4).  
Hold the  
button allow you to skip forwards.  
B. During Mp3 mode, press  
button allow you to track forwards.  
Hold the  
button allow you to skip forwards.  
For Mp3 playing(MP3 model only), these two buttons act as the digit 8 & 9 key.  
C. During RADIO mode, press and hold  
manual search channel.Then press  
4.BAND BUTTON  
or  
for more than 2 seconds you can  
, you can have auto search channel.  
or  
Press it to select your desired radio band and the band which is selected will be displayed  
on LCD.  
Press it hold for more than 2 seconds can have LOUD mode.  
LOUD MODE:  
When reduce the volume to half level, press it to enhance the bass effect.  
For Mp3 playing(MP3 model only), this button can act as the ENTER key.  
5.CLOCK BUTTON  
Press it to display time on LCD for few seconds.Press it hold and then press  
button to adjust hour or minute.  
or  
OPEN BUTTON  
6.POWER BUTTON  
Press it to turn on or off the unit.  
7.AF BUTTON(for RDS model only)  
AF [ALTERNATIVE FREQUENCIES](For RDS only)  
( FIG.1)  
( FIG.2)  
When pressed short, AF switching mode is selected and the state of AF switching mode is  
displayed by AF segment in display  
Segment off: AF switching mode off.  
Segment on: AF switching mode on, and has RDS information.  
PROTECTIVE CASE  
Segment flashing: AF switching mode is selected, but RDS information is not received yet.  
When AF switching mode is selected, the radio checks the signal strength of AF all the time.  
The interval of checking time of each AFs depends on the signal strength of current station,  
from a few minute for strong station to a few seconds for weak station. Everytime that new  
AF is stronger than current station, it switches over to that frequency for very short time, and  
NEW FREQUENCY is displayed for 1-2 second. Because the mute time of AF switching or  
checking time is very short, it is almost inaudible in case of normal program.  
When pressed long, it is activated of regional mode on /off .  
Regional mode ON  
AF switching or PI SEEK is implemented to the station which have all PI codes are the  
same as current station.  
REG of individual segment is turned on also together with displaying REG ON numeric  
3
8
INSTALLATION  
BASIC OPERATION  
display for a few seconds.  
Regional mode OFF  
The regional code in the format of PI code is ignored when AF switching or PI SEEK is  
implemented.  
DASH BOARD  
REG of individual seg. is turned off together with displaying  
REG OFF on numeric display for a few seconds.  
11-12-13-14-15-16. PRESET MEMORY BUTTONS  
A). To memorize the current frequency, press any one of the six preset Buttons hold for more  
than 2 seconds.  
B). To recall the preset memory, press one of the preset buttons [0-6].  
C) RADIO MODE  
METAL MOUNTING STRAP  
HEX NUT  
SPRING WASHER  
CONSOLE  
PLAIN WASHER  
TAPPING SCREW  
SLIDE BRACKET HOUSING  
When pressed short, these keys select a preset station directly, When pressed longer than  
one seconds,  
HEX BOLT  
current station is stored in preset memory bank. When PTY mode is selected, the preset  
memory buttons is shared as follows:  
PTY music group - - PTY speech group - - OFF MUSIC SPEECH  
1. POP M, ROCK M  
2. EASY M, LIGHT M  
3. CLASSICS, OTHER M  
4. JAZZ, COUNTRY  
5. MATION M, OLDIES  
6. FOLK M  
1. NEWS, AFFAIRS, INFO  
2. SPORT, EDUCATE, DRAMA  
3. CULTURE, SCIENCE, VARIED  
4. WEATHER, FINANCE, CHILDREN  
5. SOCIAL, RELIGION, PHONEIN  
6. TRAVEL, LEISURE, DOCUMENT  
D). In CDP mode, press 1PAU button to pause CDP playing, press it again to resume CDP  
playing.  
E). In CDP mode, press 2SCN button to play the first 10 seconds part of each song, press it  
again to stop scanning and retain playing the song currently selected.  
F). In CDP mode, press 3RPT button to play the current track repeatedly. Press it again to  
cancel this mode.  
G). In CDP mode, press 4SHF button to play the track in random order. Press it again to  
cancel this mode.  
H).In CDC mode M5/M6: It moves to up or down the DISC, then play.  
17.APS/MP3 BUTTON  
While installing the front panel,  
please mount the left side first,  
then push the right side.  
In radio mode:  
When short pressing, the radio searches for each preset station.  
When the field strength level is more than the threshold level of stop level, the radio is  
holding at that preset number for few secretary with releasing mute, and than searches  
again. In FM band, FM 1, FM 2 and FM 3 is checked one at a time. When long pressing (more  
than 1 second),Zhe radio searches from the current frequency and checks the signal streng  
th level until 1 cycle search is finished. And then 6 strongest stations are preset to the corres  
ponding preset number. The AS operation is implemented in the each band of selected band.  
When the AS operationis finished, the radio executes the preset scan.  
In MP3 mode, press 0-9 and ENTER button to play the track in 1-108 number.  
18.MODE BUTTON  
TAPPING SCREW (M1.7X4 KM BLACK)  
Press it repeatedly to select CDP, AUX and RADIO mode in sequence and circulation.  
For SUB WOOFER function(optional), press and hold for more than 2 seconds can have  
WOOFER Mode.  
For Mp3 playing(MP3 model only), this button can act as the digit 7 key.  
19.PTY(PROGRAM TYPE) BUTTON  
This key is operated as follows:  
PTY MUSIC group- - PTY SPEECH group- - PTY OFF  
While selecting PTY TYPE, its selection is implemented by preset buttons as described in preset key.  
7
4
BASIC OPERATION  
ELECTRIC CONNECTION  
When PTY is selected, the radio starts to search corresponding PTY information, and stops if the  
FOR 4X40W  
corresponding PTY information is detected.  
If corresponding PTY information is not existed any more, PTY type is automatically exit to  
normal mode.  
20.TA BUTTON(for RDS model only)  
AUX cable(optional)  
ANTENNA CONNECTOR  
RCH RED  
LCH WHITE  
TAfunction [TRAFFIC ANNOUNCEMENT] BUTTON(For RDS only)  
When pressed short, it is activated as TA mode on or off.  
OR  
When TA mode is on and traffic announcement is transmitted:  
1).When the unit is in CD mode, it will switch to radio mode temporarily.  
2).Temporary switch over to an EON linked station when EON detects a traffic  
announcement on that other program.  
CDCcannector(optional)  
IGNITION  
SWITCH(B+)  
RED  
0.5A  
FUSE BOX  
YELLOW  
FRONT RCA OUTPUT  
CABLE(optional)  
MEMORY(B+)  
RCH RED  
LCH WHITE  
3).If the volume level was under the threshold point, it will be raised to the threshold point.  
But the user changed the volume level which was more than the threshold point(min. TA  
volume level),it will be set to the last level.  
BLACK  
BLUE  
GROUND(B-)  
AUTO  
ANTENNA  
FRONT  
FRONT  
When pressed long , it is selected EONTA LOCAL / EONTA DISTANCE mode.  
The purpose of this key is to reduce unwanted EON TAswitching, which EON TA  
information was received from current station and the radio switched to that EON  
linked station, but no information could not be received because the EON linked  
station is located too far from that area.  
So the radio is switched back to current station again.  
In above operation, a customer listen to a wrong program or mute sound for a while.  
- EONTA LOCAL mode  
WHITE  
GREY  
WHITE/BLACK  
GREY/BLACK  
Lch SPK  
REAR  
Rch SPK  
REAR  
GREEN  
VIOLET  
VIOLET/BLACK  
GREEN/BLACK  
Rch SPK  
Lch SPK  
When the filed strength level of EON linked is less than the threshold level, the radio  
does not switch that station, and a customer can hardly listen to any disturbances.  
When EONTA LOACL mode is selected, EONTA LO on numeric display is indicated  
for a few seconds.  
FOR WOOFER( 4X40W)  
- EONTA DISTANCE mode  
AUX cable(optional)  
ANTENNA CONNECTOR  
EON TA switching is try to implemented by the information of current station .  
When EONTA DISTANCE mode is selected, EONTADX on numeric display is  
indicated for a few seconds.  
RCH RED  
LCH WHITE  
OR  
SUB WOOFER  
RCA  
21.SCAN BUTTON  
CDCcannector(optional)  
IGNITION  
SWITCH(B+)  
GREEN  
RED  
0.5A  
Press it to scan up by one channel step with station detection. If a valid signal has detected,  
the current frequency is blinked with in 5 seconds, then press it again to stop scan and  
remain the current frequency; otherwise, the unit continue to scan up by one channel step  
with station detection 5 seconds later.  
FUSE BOX  
YELLOW  
FRONT RCA OUTPUT  
CABLE(optional)  
MEMORY(B+)  
RCH RED  
LCH WHITE  
BLACK  
BLUE  
GROUND(B-)  
AUTO  
ANTENNA  
FRONT  
22.DSP BUTTON  
FRONT  
Press it to switch between 4 preset equalizer curves:FLAT,CLAS,POP M,ROCK M,The  
sound quality will be changed.  
23.MUTE BUTTON  
Press it to eliminate the sound immediately.  
24.FLASHING LED  
If the front panel is not on the main unit, LED will be flashing.  
25.RESET  
RESET button is placed on the housing and must be activated with either a  
ballpoint pen or thin metal object. The RESET button is to be activated for the  
following reasons:  
WHITE  
GREY  
WHITE/BLACK  
GREY/BLACK  
Lch SPK  
REAR  
Rch SPK  
REAR  
GREEN  
VIOLET  
VIOLET/BLACK  
GREEN/BLACK  
Rch SPK  
Lch SPK  
-Initial installation of the unit when all wiring is completed.  
-All the function buttons do not operate.  
-Error symbol on the display.  
Note: If press RESET button, the unit can't work yet, please use a cotton swab  
soaked in isopropyl alcohol to clean the socket on the back of the front panel.  
NOTE:  
In spite of having any kinds of speaker system, must use 4 ohms  
impedance of speaker to reduce the distortion during high volume  
level.  
5
6

Lenovo Personal Computer Q700 User Manual
Lincoln Electric Welder FX450 User Manual
Lindy Computer Accessories 51245 User Manual
Makita Power Screwdriver 6831D User Manual
Makita Saw 4303C User Manual
Maxtor DVR 4 Channel DVR Digital Video Recorder User Manual
Maytag Washer MAV5000 User Manual
Melissa Vacuum Cleaner 740 114 User Manual
Memorex Digital Photo Frame MDF0722 WLDB User Manual
Midland Radio Weather Radio WR120 User Manual