La Crosse Technology Weather Radio 308 145 User Manual

The CH switch is set to Channel 1 by default. Confirm channel 1 is selected.  
Within 3 minutes the Weather Station will beep and then show readings in the  
Outdoor temperature area on the LCD.  
TIME ZONE: EST will flash. Press and release the +/RCC or -/°C/°F button to  
select a different Time Zone: AST=Atlantic, EST= Eastern, CST= Central, MST=  
Mountain, PST= Pacific, AKT= Alaska, HAT=Hawaiian time zone. Press the SET  
button to confirm and move to the next item.  
Note: Use Alkaline batteries (or Lithium for temperatures below - 20°F / -28.8°C).  
DAYLIGHT SAVING TIME: DST will flash and the word ON. Press and release  
the +/RCC or -/°C/°F button to turn this to OFF if you do not observe DST. Press  
the SET button to confirm and move to the next item.  
12/24 HOUR TIME: 12H will flash. Press and release the +/RCC or -/°C/°F button  
to select 24H. Press the SET button to confirm and move to the next item.  
HOUR: The hour will flash. Press and release the +/RCC or -/°C/°F button to  
select the correct hour. Press the SET button to confirm and move to the next  
item.  
MINUTES: The minutes will flash. Press and release the +/RCC or -/°C/°F button  
to select the correct minutes. Press the SET button to confirm and move to the  
next item.  
YEAR: The year will flash. Press and release the +/RCC or -/°C/°F button to  
select the correct year. Press the SET button to confirm and move to the next  
item.  
TROUBLESHOOTING:  
Wireless Color Weather Station  
Model: 308-145 | Quick Setup Guide  
If the Weather Station does not show the outdoor temperature after 3 minutes,  
remove the a/c power adapter and all batteries from both units and start the setup  
process again.  
If the outdoor temperature does not show up after a second attempt, please slide  
open the battery cover of the outdoor transmitter to reveal the TX button (which is  
under the °C/°F button, push down on the TX button for 3 seconds to send a  
wireless signal to the Weather Station.  
On the Weather Station, hold the CH button for 3-5 seconds to search for the  
transmitter.  
For optimal 433 MHz signal reception, the outdoor transmitter should be placed  
within 200 feet (60 meters) from the indoor Weather Station.  
INTRODUCTION:  
The Wireless Color Weather Station features radio-controlled time, weather  
forecast, indoor and outdoor temperature/humidity as well as heat index and dew  
point, on a stylish, colorful, and easy to read display. Use the integrated USB  
charging port to charge your devices when the Weather Station is plugged into a  
power outlet.  
WIRELESS COLOR WEATHER STATION:  
POSITIONING THE WIRELESS OUTDOOR TEMP./HUMIDITY TRANSMITTER  
Once the Weather Station shows the outdoor temperature, place it and the  
transmitter in the desired locations and wait approximately 1-hour before  
permanently mounting the transmitter to ensure that there is proper reception. The  
transmitter should be mounted vertically, in a shaded, protected area, at least 6 feet  
from the ground to avoid damage and ensure accurate readings. The transmitter is  
water resistant, not waterproof and should not be placed anywhere it will become  
submerged in water or subject to standing water or snow.  
MONTH: The month will flash. Press and release the +/RCC or -/°C/°F button to  
select the correct month. Press the SET button to confirm and move to the next  
item.  
DATE: The date will flash. Press and release the +/RCC or -/°C/°F button to select  
the correct date. Press the SET button to confirm and exit the program menu  
Note: The Day of the Week will set automatically when the year, month and date  
are set.  
FAHRENHEIT/CELSIUS: Press and release the -/°C/°F button once on the  
Weather Station, to switch from Fahrenheit to Celsius.  
WALL MOUNT  
.
Choose a shaded location (under an overhang) for the transmitter that  
is within the confirmed wireless reception range of the Weather  
Station for accuracy.  
AUTO (channel scroll) - AUTO will appear in the outdoor temperature/humidity  
area when multiple transmitters are received and the Weather Station is set to scroll  
through the channels automatically.  
Press and release the CH button repeatedly until the word AUTO shows. The  
Weather Station will rotate through all available channels.  
Press and release the CH button once to show only one channel continually.  
The Weather Station can receive up to 3 outdoor transmitters.  
Extra TX14TH-LCD-G transmitters may be found online or at your retailer to monitor  
remote temperature and humidity of up to 3 locations within a 200 Ft wireless range  
of the Weather Station.  
.
.
Install one mounting screw (not included) into a wall leaving  
approximately ½ of an inch (12.7mm) extended.  
Place the hanging hole (on the back of the transmitter) onto the  
mounting screw and gently slide the transmitter down to secure it.  
IMPORTANT: For true temperature and humidity readings, mount the transmitter  
out of direct sunlight on a North-facing wall or in any other well shaded area like  
under an eave or deck rail. The maximum transmitting range in open air is over 200-  
feet (60 meters). Obstacles such as walls, windows, stucco, concrete, and large  
metal objects can reduce the range. Place the transmitter at least 6 feet in the air to  
improve signal transmission.  
Note: When only one transmitter is connected, you cannot see other channels.  
SETUP INSTRUCTIONS STEP BY STEP:  
WWVB RADIO CONTROLLED TIME  
The National Institute of Standards and Technology (NIST) WWVB radio station is  
located in Ft. Collins, Colorado. It transmits the exact WWVB time signal  
continuously throughout the United States at 60 kHz. The signal can be received up  
to 2,000 miles away through the internal antenna in the Weather Station. However,  
due to the nature of the Earth’s Ionosphere, reception is very limited during daylight  
hours. The Weather Station will search for a signal every night when reception is  
best. The WWVB radio station derives its signal from the NIST Atomic Clock in  
Boulder, Colorado.  
THE WWVB RECEPTION ICON with full signal strength will appear on  
screen if the reception of the WWVB atomic time is successful.  
The tower icon is solid: The Weather Station has received the WWVB signal.  
No tower icon shows: The Weather Station was unable to receive a signal.  
Reposition the Weather Station for better signal reception or try again at bedtime.  
The Weather Station will start searching at UTC: 07:00. If there is no reception on  
the first attempt, it will try again at 08:00, 09:00, 10:00 and 11:00 for at least 2 to  
10 min.  
STEP 1: (optional battery operation)  
Remove battery cover from the Weather Station: Slide tab to right and pull out to  
remove the cover.  
Insert 3 NEW AA batteries (not included) into the back of the Weather Station.  
Observe the correct polarity (see marking inside the battery compartment).Do  
NOT mix old and new batteries.  
The Weather Station will light up and  
show, indoor temperature, humidity and  
channel 1.  
BUTTON FUNCTIONS:  
Press and Release  
Button  
Hold 3-5 seconds  
Functions  
Move through program menu  
Confirm setting.  
Enter program menu,  
set time, date, etc.  
SET  
View Alarm  
Activate/Deactivate Alarm  
ALARM  
+/RCC  
Alarm set  
Search for WWVB  
1 step forward (setup)  
signal  
Fast  
advance (setup)  
STEP 2:  
Insert the 5-volt a/c power adapter into  
the designated area on the back of the  
Weather Station.  
Plug the a/c power adapter into a wall  
outlet for continuous backlight  
(ON/OFF), and dimmer feature. (Backlight will illuminate for 8 seconds when using  
only battery power with a press/release of the SNOOZE/LIGHT button.)  
IMPORTANT: When operating on a/c power, to avoid interference, the backlight  
will turn off while the Weather Station searches for the WWVB signal. The  
backlight returns after a 2-10 minute search.  
Select temperature in °C/°F  
1 step backward (setup)  
-/°C/°F  
Fast backward (setup)  
1-time MAX values  
2-times MIN values  
1-time Heat Index  
2-times Dew Point  
Resets all MIN / MAX  
values  
MIN/MAX  
If the WWVB signal is strong it may establish reception in ABOUT 2-3 minutes.  
If the signal is marginal it will try to obtain a signal for up to 10 minutes.  
IMPORTANT: When operating on a/c power, to avoid interference, the backlight  
will turn off while the Weather Station searches for the WWVB signal. The  
backlight will return after the 2-10 minute search which occurs during the late night  
or early morning hours.  
HEAT/DEW  
Switch channels outdoor  
(multiple transmitters)  
Search for remote  
transmitter  
Turn continuous  
backlight ON or OFF  
(a/c adapter)  
CH  
LIGHT HI/LO  
HOLD ON/OFF  
Dim backlight for night time  
Note: In case the Weather Station is not able to detect the WWVB-signal  
(disturbances, transmitting distance, etc.); the time may be manually set.  
STEP 3:  
Activates backlight when  
using only batteries  
Trigger snooze alarm  
Ensure that the transmitter is within 10  
feet of the Weather Station.  
Remove battery cover from transmitter:  
Slide the battery cover down and lift off  
the back.  
Insert 2 NEW AA batteries into the  
TX14TH-LCD-G transmitter. Observe  
the correct polarity.  
The temperature, humidity and channel  
will be displayed on the LCD of the transmitter.  
Press the °C/°F button on the transmitter to switch from Fahrenheit to Celsius.  
LIGHT/SNOOZE  
(top)  
BACKLIGHT:  
A/C adapter: The backlight is on continuously when operating the Weather Station  
with the 5-volt a/c adapter.  
HIGH: The backlight is defaulted to HI when the Adapter is in use.  
LO: Press and release the LIGHT HI/LO button to dim the backlight. Press and  
release again to return to full strength.  
Note: When the Adapter is NOT in use, the High/Lo light feature is not available.  
OFF: Hold the HOLD ON/OFF button for 5 seconds, until the station beeps, to  
turn the backlight off, to sleep.  
PROGRAM MENU:  
The SET button will move through the program menu.  
The +/RCC or -/°C/°F button will change the value.  
WWVB ON / OFF: Hold the SET button 5 seconds and WWVB and the word ON  
will flash. Press and release the +/RCC or -/°C/°F button to turn WWVB to OFF if  
you do NOT wish to use WWVB reception (manual set time/date). Press the SET  
button to confirm and move to the next item.  
 

Lasko Fan 675900 User Manual
Leica Digital Camera R Lenses User Manual
LG Electronics Portable DVD Player M70 User Manual
Life Fitness Elliptical Trainer 93X 0XXX 04 User Manual
Manhattan Computer Products Computer Hardware 160391 User Manual
Marantz Stereo Amplifier 541110275035M User Manual
Mattel Drums 5281 User Manual
Meade Telescope RB 70 User Manual
Memorex MP3 Player MPD8819 User Manual
METRObility Optical Systems Switch R125 34 User Manual