Kenwood GPS Receiver DDX5036 User Manual

GPS NAVIGATION SYSTEM  
DNX SERIES  
DNX5360 DNX5360M  
MONITOR WITH DVD RECEIVER  
DDX SERIES  
DDX5036 DDX5036M  
INSTALLATION MANUAL  
© B54-4766-10/01 (MW/M2W/XW)  
 
This unit has the cooling fan to decrease the internal  
temperature. Do not mount the unit in a place where the  
cooling fan of the unit are blocked. Blocking these openings  
will inhibit the cooling of the internal temperature and  
¤
Mounting and wiring this product requires skills and  
experience. For safety’s sake, leave the mounting and wiring  
work to professionals.  
result in malfunction.  
Make sure to ground the unit to a negative 12V DC power  
supply.  
Cooling fan  
Do not install the unit in a spot exposed to direct sunlight  
or excessive heat or humidity. Also avoid places with too  
much dust or the possibility of water splashing.  
Do not use your own screws. Use only the screws provided.  
If you use the wrong screws, you could damage the unit.  
If the power is not turned ON (“PROTECT” is displayed),  
the speaker wire may have a short-circuit or touched the  
chassis of the vehicle and the protection function may  
have been activated. Therefore, the speaker wire should be  
checked.  
If your car’s ignition does not have an ACC position, connect  
the ignition wires to a power source that can be turned on  
and off with the ignition key. If you connect the ignition  
wire to a power source with a constant voltage supply, as  
with battery wires, the battery may die.  
If the console has a lid, make sure to install the unit so that  
the faceplate will not hit the lid when closing and opening.  
If the fuse blows, first make sure the wires aren’t touching  
to cause a short circuit, then replace the old fuse with one  
with the same rating.  
Insulate unconnected wires with vinyl tape or other similar  
material. To prevent a short circuit, do not remove the caps  
on the ends of the unconnected wires or the terminals.  
Connect the speaker wires correctly to the terminals to  
which they correspond. The unit may be damaged or fail to  
work if you share the - wires or ground them to any metal  
part in the car.  
When only two speakers are being connected to the  
system, connect the connectors either to both the front  
output terminals or to both the rear output terminals (do  
not mix front and rear). For example, if you connect the +  
connector of the left speaker to a front output terminal, do  
not connect the - connector to a rear output terminal.  
After the unit is installed, check whether the brake lamps,  
blinkers, wipers, etc. on the car are working properly.  
Mount the unit so that the mounting angle is 30° or less.  
Do not press hard on the panel surface when installing the  
unit to the vehicle. Otherwise scars, damage, or failure may  
result.  
¤ CAUTION  
Install this unit in the console of your vehicle.  
Do not touch the metal part of this unit during and  
shortly after the use of the unit. Metal part such as  
the heat sink and enclosure become hot.  
|
English  
3
 
Connection  
If you connect the ignition wire (red) and the battery  
wire (yellow) to the car chassis (ground), you may  
cause a short circuit, that in turn may start a fire. Always  
connect those wires to the power source running  
through the fuse box.  
¤
Ignition key  
switch  
ACC  
A
B
Ignition wire (Red)  
A
Car fuse box  
Battery wire (Yellow)  
Car fuse box  
(Main fuse)  
B
FM/AM  
antenna input  
Antenna Cord  
Ground wire (Black) -  
(To car chassis)  
C
C
Battery  
Connect to the vehicle's parking brake  
detection switch harness.  
Parking sensor wire (Light Green)  
PRK SW  
For the sake of safety, be sure to connect the parking sensor.  
Reveres sensor wire (Purple/White)  
Connect to vehicle's reverse lamp harness when  
using the optional rear view camera.  
Steering remote control wire (Light Blue/Yellow)  
To steering remote  
To use the steering wheel remote control feature, you need to  
an exclusive remote adapter (not supplied) matches your car is  
required. When this terminal is not in use, leave its cap on.  
Dimmer control wire (Orange/White)  
Mute control wire (Brown)  
To car light control switch  
Connect to the terminal that is grounded when either  
the telephone rings or during conversation.  
To connect the Kenwood navigation system,  
consult your navigation manual.  
Depending on what antenna you are using,  
Motor antenna control wire (Blue)  
Power control wire (Blue/White)  
connect either to the control terminal of the motor antenna, or to the  
power terminal for the booster amplifier of the film-type antenna.  
When using the optional power amplifier,  
connect to its power control terminal.  
If no connections are made, do not let the cable come out from the tab.  
|
4
DNX SERIES/ DDX SERIES  
 
GPS Antenna (Accessory 2)  
(see page 8)  
FUSE ( 15A )  
Accessory 1  
REVERSE  
STEERING WHEEL  
REMOTE INPUT  
REMOTE CONT  
White/Black  
To front left speaker  
To front right speaker  
To rear left speaker  
To rear right speaker  
+
+
+
+
White  
Gray/Black  
ILLUMI  
MUTE  
Gray  
Green/Black  
Green  
Purple/Black  
ANT. CONT  
P CONT  
Purple  
|
English  
5
 
System Connection  
USB device  
(commercially available)  
USB terminal  
Rear View Camera input  
• Visual input (Yellow)  
Audio/Visual output  
• Visual output (Yellow)  
• Audio left output (White)  
• Audio right output (Red)  
Visual input (iPod/AV input 2 switchable)  
Resistance-free mini plug (3.5φ)  
Audio input (iPod/AV input 2 switchable)  
Resistance-free stereo type mini plug (3.5φ)  
Rear Preout  
• Audio left output (White)  
• Audio right output (Red)  
Front Preout  
• Audio left output (White)  
• Audio right output (Red)  
Subwoofer Preout  
• Audio left output (White)  
• Audio right output (Red)  
|
6
DNX SERIES/ DDX SERIES  
 
Optional Accessory Connection  
iPod  
(commercially available)  
KCA-iP301V  
(Optional Accessory)  
Audio Output (Black)  
Visual Output (Yellow)  
(DDX5036/ DDX5036M only)  
USB terminal  
Navigation System  
(Optional Accessory)  
KCA-BT200 (Optional Accessory) input  
TV Tuner (Optional Accessory)  
Connection cable  
(Included in the  
Navigation System)  
T V A N T E N N A I N P U T  
Navigation units that can be connected  
to this unit. (As of December, 2009):  
KNA-G630  
R O U N I T  
M O O T N I T  
KNA-G630CN  
For latest information, access the  
Connection cable  
(Included in the TV tuner)  
|
English  
7
 
Installing the GPS Antenna  
(DNX SERIES only)  
GPS antenna is installed inside of the car. It should  
be installed as horizontally as possible to allow easy  
reception of the GPS satellite signals.  
To mount the GPS antenna inside your vehicle:  
1. Clean your dashboard or other surface.  
2. Peel the backing off of the adhesive on the bottom  
of the metal plate (accessory 3).  
3. Press the metal plate (accessory 3) down firmly on  
your dashboard or other mounting surface. You can  
bend the metal plate (accessory 3) to conform to  
a curved surface, if necessary.  
4. Place the GPS antenna (accessory 2) on top of the  
metal plate (accessory 3).  
Accessory 2  
Accessory 3  
¤
Depending on the type of car, reception of the GPS satellite  
signals might not be possible with an inside installation.  
The GPS antenna should be installed at a position that is  
spaced at least 12 inch (30 cm) from cellular phone or other  
transmitting antennas. Signals from the GPS satellite may be  
interfered with by these types of communication.  
Painting the GPS antenna with (metallic) paint may cause a  
drop in performance.  
|
8
DNX SERIES/ DDX SERIES  
 
Installing the Escutcheon  
Installing the Escutcheon  
For Toyota/Scion  
1. Cut out accessory 5 as illustrated.  
Cutting line  
1. Attach accessory 4 to the unit.  
Accessory 5  
Accessory 4  
2. Fold double-sided adhesive (accessory 6) along  
the slit and attach it to accessory 5 cut-out  
against the center rib as illustrated. Use 2 pieces of  
accessory 6 for 1 accessory 5 cut-out.  
For General Motors  
1. Cut out accessory 5 to meet the shape of the  
opening of the center console.  
2. Attach accessory 5 to the unit.  
3. Attach accessory 5 cut-out to the unit.  
Cut out to meet the shape of  
the opening in the vehicle.  
Accessory 6  
Accessory 5  
|
English  
9
 
Installation for Monitor/Player Unit  
Installation on Toyota, Nissan or Mitsubishi Car using Brackets  
Accessory 7 (M5x6mm)  
or Accessory 8 (M5x7mm)  
Car Bracket  
Accessory 7 (M5x6mm)  
or Accessory 8 (M5x7mm)  
|
10  
DNX SERIES/ DDX SERIES  
 
|
English  
11  
 

Insignia Speaker NS PLTPSP User Manual
Insignia TV DVD Combo NS LTDVD32 09 User Manual
Ironman Fitness Treadmill 320t User Manual
Jenn Air Oven JJW9627DDB User Manual
JVC CD Player KD AR360 User Manual
JVC Flat Panel Television 0508TSH II IM User Manual
Kawai Musical Instrument CP205 CP185 User Manual
Kenmore Air Conditioner 35132 User Manual
KitchenAid Cooktop KECC568RPB01 User Manual
Kodak Film Camera 65MM User Manual