Invacare Mobility Aid 1110266 User Manual

Bolt-In-Place/Spring Button Front Rigging Kit  
Assembly and Installation Instructions  
Kits No. 1110266 and 1121271  
SAVE THESE INSTRUCTIONS  
NOTE: Check ALL parts for shipping damage. In case of shipping damage, DO NOT use. Contact  
Carrier/Dealer for further instruction.  
SAFETY SUMMARY  
To ensure the safe installation of the Bolt-In-Place/Spring Button Front Rigging  
Kit, these instructions MUST be followed:  
WARN IN G  
DO NOT install or use this equipm ent without first reading and understanding  
these instructions and the Owners Manual supplied with the wheelchair. If you  
are unable to understand the W arnings, Cautions or Instructions, contact a  
healthcare professional, dealer or technical personnel before attem pting to  
install this equipm ent - otherwise, injury or dam age m ay occur.  
IN STA LLA TION WA RN IN G  
After ANY adjustments, repair or service and before use, make sure all attaching  
hardware is tightened securely - otherwise injury or damage may occur.  
Bolt-In-Place Front Rigging Kit 1110266 contains the following items:  
DESCRIPTION  
QUANTITY  
Riv Nut  
Button Head Screw  
1/8-inch Hex key  
2
2
1
Spring Buton Front Rigging kit 1112127 contains the following items:  
DESCRIPTION  
QUANTITY  
Spring buttons  
4
IN STA LLIN G TH E BOLT-IN -PLA CE FOOTPLA TE KIT  
(FIGURE 1 )  
NOTE: This kit mounts the footplate assembly to the front rigging support so that tools are required  
to remove or adjust the footrest assembly.  
1. Remove the front rigging from the wheelchair. Refer to the wheelchair owners  
manual shipped with wheelchair.  
2. Pull up on the cam lock lever to unlock the cam.  
NOTE: The elevating legrest has two (2) sets of release buttons, one (1) set above the other. Each  
set will be visible one at a time allowing finer footplate height adjustment.  
3. Push IN and hold the release button as shown in DETAIL “A” of FIGURE 1.  
4. Rotate the lower footplate assembly 1/4 turn.  
Part No. 1114831  
1
Bolt-In-Place/Spring Button  
Front Rigging Kit  
 
BOLT-IN -PLA CE H EIGH T A DJUSTMEN T (FIGURE 1 )  
NOTE: This procedure applies to the swingaway footrests and swingaway elevating legrest.  
1. Remove the swingaway front rigging. Refer to INSTALLING/REMOVING THE  
FRONT RIGGINGS in the owners manual shipped with wheelchair.  
NOTE: Lay the front rigging assembly on a flat surface to simplify this procedure.  
2. Pull the cam lock lever UP to UNLOCKED position.  
3. Using a screw driver to hold the riv nut in position, remove the button head screw  
from the riv nut.  
4. Remove the riv nut and button head screw securing the footplate assembly to the  
front rigging support.  
5. Adjust the footplate assembly height by aligning the desired adjustment holes in the  
upper front rigging support and footplate assembly.  
6. From the outside of the swingaway front rigging, insert the riv nut through both the  
front rigging support and the footplate assembly.  
7. From the inside of the swingaway front rigging, insert the button head screw through  
the appropriate adjustment hole and thread into the riv nut.  
8. Using a screwdriver to hold the riv nut in position, securely tighten the button head  
screw. Torque to 32 in-lbs.  
9. Rotate cam lock lever DOWN to LOCKED position.  
10. Repeat STEPS 1-9 to adjust the remaining footrest.  
11. Reinstall the swingaway front rigging. Refer to INSTALLING/REMOVING THE  
FRONT RIGGINGS in the owners manual shat shipped with wheelchair.  
Part No. 1114831  
3
Bolt-In-Place/Spring Button  
Front Rigging Kit  
 
IN STA LLIN G TH E SPRIN G BUTTON FRON T RIGGIN G  
KIT (FIGURE 2 )  
NOTE: This kit allows tool-less removal or adjustment of the footplate assembly.  
1. Remove the front rigging from the wheelchair. Refer to the wheelchair owners  
manual shipped with wheelchair.  
\
2. Pull the cam lock lever UP to UNLOCKED position.  
3. Using a screw driver to hold the riv nut in position, remove the button head screw  
from the riv nut as shown in DETAIL “A” of FIGURE 2.  
4. Remove the riv nut and button head screw securing the footplate assembly to the  
front rigging support.  
5. Remove the footplate assembly from the upper front rigging support.  
6. Perform one of the following as shown in DETAIL “B” OF FIGURE 2:  
A. FOOTRESTS:  
With the spring pointing UP, insert the spring button into the footplate tube  
so that the release buttons FULLY protrude through the top set of mounting  
holes.  
B. ELEVATING LEGRESTS AND FOOTRESTS WITH ADJUSTABLE ANGLE  
FOOTPLATES:  
With the spring pointing DOWN, insert the bottom spring button into the  
footplate tube so that the release buttons FULLY protrude through the  
bottom set of mounting holes.  
With the spring pointing UP, insert the top spring button into the footplate  
tube so that the release buttons FULLY protrude through the top set of  
mounting holes.  
NOTE: The elevating legrest has two (2) sets of release buttons, one (1) set above the other. Each  
set will be visible one at a time allowing finer footplate height adjustment.  
7. Insert the footplate tube into the front rigging support.  
8. Push IN the release buttons and reposition the footplate assembly to the desired  
height.  
9. Ensure that the release buttons fully protrude from holes on both sides of the front  
rigging support.  
10. Rotate cam lock lever DOWN to LOCKED position.  
11. Reinstall the swingaway front rigging assembly. Refer to the owners manual shipped  
with wheelchair.  
12. Ensure Release buttons are properly seated and FULLY protrude through the  
adjustment holes before use.  
13. Repeat this procedure for the other footplate, if necessary.  
Bolt-In-Place/Spring Button  
Front Rigging Kit  
4
Part No. 1114831  
 
DETAIL “A”  
DETAIL “B”  
Front Rigging Support  
Spring  
Front Rigging Support  
Riv Nut  
Spring Button  
Release  
Button  
Release Buttons  
Button  
Head  
Screw  
Footplate  
Assembly  
Adjustment  
Holes  
Footplate  
Assembly  
FO O TRESTS  
Spring  
Cam Lock  
Lever  
Cam  
Lock  
Lever  
Top Spring Button  
Release Buttons  
Bottom Spring Button  
NOTE: Swingaway  
footrests shown.  
NOTE: Swingaway  
footrest shown.  
Spring  
ELEVATING LEGRESTS/  
FO O TRESTS W ITH  
ADJUSTABLE ANGLE  
FO O TPLATES  
FIGURE 2 - INSTALLING THE SPRING BUTTO N FO O TPLATE KIT  
SPRIN G BUTTON H EIGH T A DJUSTMEN T (FIGURE 2 )  
NOTE: This procedure applies to the swingaway footrests and swingaway elevating legrest.  
1. Remove the swingaway front rigging. Refer to INSTALLING/REMOVING THE  
FRONT RIGGINGS in the owners manual shipped with wheelchair.  
NOTE: Lay the front rigging assembly on a flat surface to simplify this procedure.  
2. Pull the cam lock lever UP to UNLOCKED position.  
NOTE: The elevating legrest has two (2) sets of release buttons, one (1) set above the other. Each  
set will be visible one at a time allowing finer footplate height adjustment.  
3. Push IN the release buttons and reposition the footplate assembly to the desired  
height.  
4. Ensure that the release buttons fully protrude from holes on both sides of the front  
rigging support.  
5. Rotate cam lock lever DOWN to LOCKED position.  
6. Repeat this procedure for the other footplate, if necessary.  
7. Reinstall the swingaway front rigging assembly. Refer to INSTALLING/REMOVING THE  
FRONT RIGGING in the owners manual that shipped with wheelchair.  
8. Ensure Release buttons are properly seated and FULLY protrude through the  
adjustment holes before use.  
Part No. 1114831  
5
Bolt-In-Place/Spring Button  
Front Rigging Kit  
 
N OTES  
Bolt-In-Place/Spring Button  
Front Rigging Kit  
6
Part No. 1114831  
 
N OTES  
Part No. 1114831  
7
Bolt-In-Place/Spring Button  
Front Rigging Kit  
 
MADE IN MEXICO  
Invacare Corporation  
USA  
One Invacare Way  
Elyria, Ohio USA  
44036-2125  
Invacare is a registered trademark of  
Invacare Corporation.  
Yes, you can. is a trademark of  
Invacare Corporation.  
800-333-6900  
© 2003 Invacare Corporation  
Part No. 1114831  
Rev B - 07/03  
 

Ingersoll Rand Door BE365 User Manual
JBL Speaker System ECS300 User Manual
John Deere Impact Driver AT 3104 J User Manual
JVC MP3 Player XL R5020BK User Manual
Kenmore Range 970 334420 User Manual
Kenwood Car Stereo System CAW 1142 02 User Manual
King Canada Washer KPW 205 User Manual
KitchenAid Blender 5KSB555AAC User Manual
KitchenAid Outdoor Cart KFBU271T User Manual
KitchenAid Refrigerator W10635370A User Manual